AAON F1-060 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 56

AAON F1-060 Скачать руководство пользователя страница 22

22

Thermostat

Units

without

the

neutral

air

dehumidification  feature  will  operate  with
most  common  thermostats.  Units  with  the
neutral air dehumidification feature must use
thermostats  with  a  normally  closed  (NC)
dehumidification option. The following stats
have  been  approved  for  usage  with  the
dehumidification feature.

Robertshaw

Honeywell

9825i2

VisionPRO



IAQ

Filters

Open  filter  access  bracket  and  slide  correct
filter  in  with  arrow  pointing  towards  the
blower  in  the  direction  of  airflow.
Replacement filters are 20” x 20” x 1”.

Charging Refrigerant

The  unit  comes  with  full  charge  based  on  a
25-foot  line  set.  Charging  a  system  in  the
field  must  be  based  on  determination  of
liquid sub-cooling and evaporator superheat.
On  a  system  with  a  thermostatic  expansion
valve,

liquid

sub-cooling

is

more

representative of the charge than evaporator
superheat but both measurements must be
taken.

Before Charging

The unit being charged must be at or near
full load conditions before adjusting the
charge.

Units  equipped  with  hot  gas  reheat  must
have the hot  gas reheat  valves closed to  get
the proper charge.

Units  equipped  with  hot  gas  reheat  must  be
charged with the hot gas valve closed while
the unit is in cooling mode.

After adding or removing charge the system
must be allowed to stabilize, typically 10-15
minutes,

before

making

any

other

adjustments.

The  type  of  unit  and  options  determine  the
ranges for liquid sub-cooling and evaporator
superheat.  Refer  to  Error!  Reference  source
not found. when determining the proper sub-
cooling.

The  vertical  rise  of  the  liquid  line  must  be
known  in  order  to  adjust  the  sub-cooling
range for proper charge.

The  Clean  Air  Act  of  1990  bans  the
intentional venting of refrigerant as of
July  1,  1992.  Approved  methods  of
recovery,  recycling,  or  reclaiming
must be followed.

CAUTION

«
...
20
21
22
23
24
...
»

Содержание F1-060

























































Отзывы:

Нет отзывов