A&D AD-4329A Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 56

A&D AD-4329A Скачать руководство пользователя страница 41

AD-4329A Weighing Indicator

Page

39

9.3. Setpoint Comparison

This function includes the weighing sequence and uses for getting preset target

weight.

There are four parameters of "Final", "Preliminary", "Free fall" and "Zero band" to

use the setpoint comparison.

The result of the sequence is output to three relays.

When inputting these parameters, it is not necessary to input the F-function

f-20

again unless changing the F-function.

Caution

This function is normal batching only and can not perform

loss-in-weight.

9.3.1. Selecting Setpoint Comparison

Step 1 Press the

Operate/Standby

key to turn display off.

Press and hold the

MODE

key and press the

Operate/Standby

key to enter the F-function mode.

Step 2 Select

f-20 2

(setpoint comparison).

Step 3 Turn the display off using the

Operate/Standby

key.

9.3.2. Description of Input parameters and Outputs

Output and Condition

Parameters List

SET0 Final

Set a preset target weight.

SET1 Free fall

Set a corrective value related to closing the dribble flow gate.

SET2 Preliminary Set a begining point to use the dribble flow gate only.
SET3 Zero band

Set a value to regard as nearly zero.

9.3. Setpoint Comparison

«
...
39
40
41
42
43
...
»

Содержание AD-4329A

























































Отзывы:

Нет отзывов