AAMP Global ECHOMASTER PRO ParkAlert PS-TRUCK30 Скачать руководство пользователя

Страница: 8 / 12

Installation Guide

phone - 1-800-477-2267
email - [email protected]

Sensor Painting

Step 1

Remove the silicon gasket
and disconnect cable before
painting the sensors.
Certain colors may require a
thin coat of primer.

Step 2

Paint the front of the sensors and the
angle sleeve. Avoid getting excessive
paint on the back of the sensors.
Paint thickness should not exceed
1mm or sensors may not function
properly.

Note: Gasket is only removable on
paintable sensors.

Step 3

After the paint has fully dried, reassemble the sensors as shown below.

PS-TRUCK30

ParkAlert Digital Rear Sensing System

with Extended Harness for Trucks

Содержание ECHOMASTER PRO ParkAlert PS-TRUCK30













Результаты поиска

Содержание ECHOMASTER PRO ParkAlert PS-TRUCK30

Отзывы:

Похожие инструкции для ECHOMASTER PRO ParkAlert PS-TRUCK30

Бренды по названию

Популярные бренды

AAMP Global ECHOMASTER PRO ParkAlert PS-TRUCK30, Руководство пользователя

Результаты поиска

Содержание ECHOMASTER PRO ParkAlert PS-TRUCK30

Отзывы:

Похожие инструкции для ECHOMASTER PRO ParkAlert PS-TRUCK30

Бренды по названию

Популярные бренды