Aaeon SBC-400 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 69

background image

Chapter 3 AMI WinBIOS setup 41

Floppy Drive Seek at Boot

When this option is enabled, WinBIOS performs a Seek command
on floppy drive A: before booting the system.

System Boot Up Sequence

This option sets the sequence of boot drives (either floppy drive A:
or hard disk drive C:) that WinBIOS attempts to boot from after
POST completes. The settings are C:, A: (first C:, then A:) or A:,C:
(first A:, then C:).

System Boot Up CPU Speed

This option sets the speed of the CPU at system boot time. The
settings are High or Low.

External Cache

This option enables secondary cache memory. If Both is selected,
internal cache and external cache memory is enabled. If Internal is
chosen, only the internal cache memory in the Pentium CPU is
enabled. If Disabled is chosen, all cache memory in the Pentium
CPU is disabled.

External Cache Mode

This option selects the type of caching algorithm used by WinBIOS
and the computer for L2 (external) secondary cache memory. The
settings are Wr-Thr (Write-Through) or Wr-Back (Write-Back).

Turbo Switch function

When this option is set to Enabled, the externally mounted turbo
switch is enabled.

Password Checking

This option enables the password check option every time the
system boots or the end user runs Setup. If Always is chosen, a user
password prompt appears every time the computer is turned on. If
Setup is chosen, the password prompt appears if WinBIOS is
executed. The Optimal and Fail-Safe default settings are Setup.

Video ROM Shadow C000,32K

«
...
46
47
48
49
50
...
»

Содержание SBC-400






































































Отзывы:

Нет отзывов

Похожие инструкции для SBC-400

Бренд: Eaton Страницы: 10

Бренд: Lattice Semiconductor Страницы: 15

iCE40 UltraLite

Бренд: Lattice Semiconductor Страницы: 13

Бренд: Xilica Audio Design Страницы: 30

Бренд: WHOOP Страницы: 26

Бренд: Orban Страницы: 255

SuperServer 5019S-L

Бренд: Supermicro Страницы: 61

Бренд: Time domain Страницы: 64

PCIe/PXIe-6301 Series

Бренд: JYTEK Страницы: 46

Бренд: ivideon Страницы: 11

Бренд: EZCast Pro Страницы: 4

Бренд: ekwb Страницы: 2

Network Scanning Unit A

Бренд: Ricoh Страницы: 206

Бренд: Renesas Страницы: 52

Бренд: TRENDnet Страницы: 2

Бренд: Alcatel-Lucent Страницы: 8

9500S-8 - Escalade RAID Controller

Бренд: 3Ware Страницы: 46

Бренд: Curtiss-Wright Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды