Aaeon SBC-400 Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 69

background image

40 SBC-400 User's Manual

Memory Test Tick Sound

This option enables (turns on) or disables (turns off) the ticking
sound during the memory test.

Memory Parity Error Check

This option enables or disables parity error checking for system
RAM. The settings are Enabled (all system RAM parity is
checked) or Disabled (parity is checked only on the first 1 MB of
system RAM).

Hit <Del> Message Display

Disabling this option prevents the message

Hit <DEL> if you want to run Setup

from appearing when the system boots. The settings are Enabled or
Disabled.

Extended BIOS RAM Area

Specify in this option if the top 1 KB of the system programming
area beginning at 639 K or 0:300 in the system BIOS area in low
memory will be used to store hard disk information. The settings
are Top 1 K or 0:300.

Wait for <F1> If Any Error

WinBIOS POST runs system diagnostic tests that can generate a
message followed by:

Press <F1> to continue

If this option is enabled, WinBIOS waits for the end user to press
<F1> before continuing. If this option is disabled, WinBIOS
continues the boot process without waiting for <F1> to be pressed.

System Boot Up Num Lock

When On, this option turns off Num Lock when the system is
powered on so the end user can use the arrow keys on both the
numeric keypad and the keyboard.

«
...
45
46
47
48
49
...
»

Содержание SBC-400






































































Отзывы:

Нет отзывов

Похожие инструкции для SBC-400

All in One Printer

Бренд: Baracoda Страницы: 42

Бренд: EAW Страницы: 10

Бренд: 3xLogic Страницы: 2

WS-650 lite Series

Бренд: Laurell Страницы: 84

CLICK PLUS C2-02CPU

Бренд: Automationdirect.com Страницы: 10

eXtremeRAID 1100

Бренд: Mylex Страницы: 74

Бренд: Supero Страницы: 16

Бренд: Ubiquiti Страницы: 13

VIGI NVR1004H-4P

Бренд: TP-Link Страницы: 2

Бренд: ZALMAN Страницы: 18

Бренд: Procool Страницы: 2

Бренд: Kaya Instruments Страницы: 48

MP5S Plus Writer

Бренд: SONIX Страницы: 23

Бренд: LevelOne Страницы: 4

Soundweb 9088ii DSP System

Бренд: BSS Audio Страницы: 2

SPEEDTOUCH 110G

Бренд: THOMSON Страницы: 26

Бренд: LevelOne Страницы: 61

System 4 Landmark Technic Processor

Бренд: Ametek Land Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды