Aaeon SBC-400 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 69

background image

FCC STATEMENT

THIS DEVICE COMPLIES WITH PART 15 FCC RULES.
OPERATION IS SUBJECT TO THE FOLLOWING TWO
CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE
HARMFUL INTERFERENCE. (2) THIS DEVICE MUST
ACCEPT ANY INTERFERENCE RECEIVED INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED OPER-
ATION.

THIS EQUIPMENT HAS BEEN TESTED AND FOUND
TO COMPLY WITH THE LIMITS FOR A CLASS "A"
DIGITAL DEVICE, PURSUANT TO PART 15 OF THE
FCC RULES. THESE LIMITS ARE DESIGNED TO
PROVIDE REASONABLE PROTECTION AGAINTST
HARMFUL INTERFERENCE WHEN THE EQUIPMENT
IS OPERATED IN A COMMERCIAL ENVIRONMENT.
THIS EQUIPMENT GENERATES, USES, AND CAN
RADIATE RADIO FREQENCY ENERGY AND , IF NOT
INSTATLLED AND USED IN ACCORDANCE WITH THE
INSTRUCTION MANUAL, MAY CAUSE HARMFUL
INTERFERENCE TO RADIO COMMUNICATIONS.
OPERATION OF THIS EQUIPMENT IN A RESIDEN-
TIAL AREA IS LIKELY TO CAUSE HARMFUL INTER-
FERENCE IN WHICH CASE THE USER WILL BE
REQUIRED TO CORRECT THE INTERFERENCE AT
HIS OWN EXPENSE.

«
1
2
3
4
...
»

Содержание SBC-400






































































Отзывы:

Нет отзывов

Похожие инструкции для SBC-400

xStack Storage DSN-4000 Series

Бренд: D-Link Страницы: 5

Бренд: Lattice Semiconductor Страницы: 15

iCE40 UltraLite

Бренд: Lattice Semiconductor Страницы: 13

WS-650 lite Series

Бренд: Laurell Страницы: 84

Бренд: Ebyte Страницы: 14

Бренд: SeaLevel Страницы: 17

DataPlot CB1224

Бренд: B-G Instruments Страницы: 4

Бренд: Idis Страницы: 20

UniFi LED ULED-AT

Бренд: Ubiquiti Страницы: 16

CNPS5X PERFORMA

Бренд: ZALMAN Страницы: 8

Бренд: Symantec Страницы: 100

Бренд: Xtreme Страницы: 83

Бренд: VIA Technologies Страницы: 25

Бренд: Commell Страницы: 17

PowerForce G4 '47

Бренд: PowerLogix Страницы: 12

DP1.2-Vision-IP-Fiber

Бренд: G&D Страницы: 240

Бренд: ASTRO Страницы: 12

Бренд: Cambium Networks Страницы: 99

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды