A.O. Smith GTS-305-NE Скачать руководство пользователя страница 45 | Manualshive

Страница: 45 / 60

A.O. Smith GTS-305-NE Скачать руководство пользователя страница 45

Component Replacement Instructions

1. Turn off the gas supply.

2. Turn off the 120 V power supply.

3. Turn off the water supply. Drain all water

from the appliance.

4. Remove four screws securing the front panel.

Remove front panel.

Remove Fan Assembly (Figure 56)

5. Disconnect wire harness at the fan assembly.

Disconnect the air temperature thermistor
(two white wires) at the connection with the
white and orange wires within the wire
bundle.

6. Pull out the harness attached to the solenoid

on the manifold to make room to pull out the
fan assembly.

7. Remove the 2 screws that attach the fan

assembly to the bottom of the burner.

8. Loosen the ducting from the fan assembly by

pinching open the metal clamp.

9. Pull out the fan assembly.

Fan Assembly

Gas Manifold

Burner cover
plate

PC Board

Gas Control
Valve

Figure 55

2 screws

Wire harness connection
on the fan assembly

Solenoid on the manifold

Wire harness bundle
(air temperature
thermistor connection to
orange / white wires)

Ducting and
metal clamp

Figure 56

Heat Exchanger

On-Demand Gas Tankless Water Heater Service Manual

45

505i

«
...
43
44
45
46
47
...
»

Содержание GTS-305-NE





























































Отзывы:

Нет отзывов