A.O. Smith GTS-305-NE страница 25 Скачать руководство пользователя | Manualshive

Страница: 25 / 60

background image

Component Replacement Instructions

305i, 505i

1. Turn off the gas supply.

2. Turn off the 120 V power supply.

3. Turn off the water supply.

4. Remove four screws securing the front panel. Remove front panel.

5. Disconnect wire harness at the fan assembly. Disconnect the air temperature thermistor (two white

wires) at the connection with the white and orange wires within the wire bundle.

6. Pull out the harness attached to the solenoid on the manifold to make room to pull out the fan as-

sembly.

7. Loosen the ducting from the fan assembly by pinching open the metal clamp.

8. Remove the two screws that attach the fan assembly to the bottom of the burner.

9. Pull out the fan assembly.

10. Install the fan assembly by inserting the tab on the fan assembly into the slot at the base of the heat

exchanger and attaching with two screws.

11. Push ducting over fan assembly inlet and secure with metal clamp.

12. Attach the wire harness to the solenoid on the gas manifold (brown, black wires).

13. Attach the wire harness to the fan assembly (white, yellow, black, red wires).

14. Attach the air temperature thermistor (white, white wires) to the wire harness.

15. Install front panel using 4 screws.

16. Turn on water supply, power supply, and gas supply.

2 screws

Wire harness connection
on the fan assembly

Solenoid on the manifold

Wire harness bundle
(air temperature
thermistor connection to
orange / white wires)

Ducting and
metal clamp

Figure 12

Water outlet
connection

water flow servo
assembly
connection

Fan

On-Demand Gas Tankless Water Heater Service Manual

25

«
...
23
24
25
26
27
...
»

Содержание GTS-305-NE





























































Отзывы:

Нет отзывов

Похожие инструкции для GTS-305-NE

Бренд: Lasko Страницы: 4

Бренд: EBARA Страницы: 164

Бренд: IBO Страницы: 22

Бренд: iGenix Страницы: 6

Бренд: UGSI Страницы: 125

HydraPump Smart

Бренд: Watershed Innovations Страницы: 11

Бренд: Cadet Страницы: 9

Infinite Energy2 IW1000

Бренд: RBI Страницы: 156

Бренд: salmson Страницы: 20

Бренд: N'oveen Страницы: 21

Бренд: Chromalox Страницы: 4

Бренд: Oase Страницы: 70

Бренд: IMO Страницы: 11

Бренд: Lasko Страницы: 4

Бренд: Reznor Страницы: 31

HYDROMATIC HTS33A1

Бренд: Pentair Страницы: 8

Бренд: Rheem Страницы: 1

CN 04 050 EIS W

Бренд: TESY Страницы: 148

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды