manualshive.com logo in svg

A.O. Smith GTS-305-NE, Руководство по обслуживанию, Страница: 24 / 60

Поделиться
Скачать
A.O. Smith GTS-305-NE Скачать руководство пользователя страница 24

Component Replacement Instructions

 

305e/o, 505e/o

1.  Turn off the gas supply.  

2.  Turn off the 120 V power supply.  

3.  Turn off the water supply.   

4.  Remove four screws securing the front panel.  Remove front panel. 

5.  Disconnect wire harness at the fan assembly.  Disconnect the air temperature thermistor (two white 

wires) at the connection with the white and orange wires within the wire bundle. 

6.  Pull out the harness attached to the solenoid on the manifold to make room to pull out the fan as-

sembly. 

7.  Remove the two screws that attach the fan assembly to the bottom of the burner. 

8.  Pull out the fan assembly. 

9.  Install the fan assembly by inserting the tab on the fan assembly into the slot at the base of the heat 

exchanger and attaching with two screws.  

10.  Attach the wire harness to the solenoid on the gas manifold (brown, black wires). 

11.  Attach the wire harness to the fan assembly (white, yellow, black, red wires). 

12.  Attach the air temperature thermistor (white, white wires) to the wire harness. 

13.  Install front panel using 4 screws. 

14.  Turn on water supply, power supply, and gas supply. 

Two screws 

Wire harness connection 
on the fan assembly 

Solenoid on 
the manifold 

Figure 11 

Fan

On-Demand Gas Tankless Water Heater Service Manual

24

Содержание GTS-305-NE





























































Отзывы:

Нет отзывов