A.O. Smith GTS-305-NE Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 60

A.O. Smith GTS-305-NE Скачать руководство пользователя страница 35

Component Replacement Instructions

305e

1. Turn off the gas supply.

2. Turn off the 120 V power supply.

3. Turn off the water supply. Drain all water

from the appliance.

4. Remove four screws securing the front panel.

Remove front panel.

Remove Fan Assembly (Figure 29)

5. Disconnect wire harness at the fan assembly.

Disconnect the air temperature thermistor
(two white wires) at the connection with the
white and orange wires within the wire
bundle.

6. Pull out the harness attached to the solenoid

on the manifold to make room to pull out the
fan assembly.

7. Remove the 2 screws that attach the fan

assembly to the bottom of the burner.

8. Pull out the fan assembly.

9. Remove 1 screw from the water outlet

bracket. Remove the bracket by rotating and
moving it up toward the bend in the tube
where the diameter is smaller.

10. Remove 1 screw and 1 bracket at the water

flow servo assembly.

Figure 28

Fan Assembly

Gas Manifold

Burner cover
plate

PC Board

Gas Control
Valve

Figure 29

Wire
harness
connection

Solenoid

Figure 30

Water outlet
connection

Water flow servo
assembly connection

Disconnect Water Lines (Figure 30)

On-Demand Gas Tankless Water Heater Service Manual

35

Heat Exchanger

2 screws

«
...
33
34
35
36
37
...
»

Содержание GTS-305-NE





























































Отзывы:

Нет отзывов