background image

warranty information

LIMITED TWO YEAR CONSUMER WARRANTY

Directed Electronics, Inc. promises to the original purchaser, to replace this product should it prove to be
defective in workmanship or material under normal use, for a period of two years from the date of
purchase from the dealer as indicated by the date code marking of the product 

PROVIDED 

the product

was installed by an authorized Directed dealer. During this two-year period, there will be no charge for
this replacement 

PROVIDED

the unit is returned to Directed, shipping pre-paid.  If the unit is installed by

anyone other than an authorized Directed dealer, the warranty period will be one year from the date of
purchase by the dealer as indicated by the date code marking of the product. This warranty is non-
transferable and does not apply to any unit that has been modified or used in a manner contrary to its
intended purpose, and does not cover damage to the unit caused by installation or removal of the unit.
During this one-year period, there will be no charge for this replacement 

PROVIDED

the unit is returned

to Directed, shipping pre-paid. This warranty is void if the product has been damaged by accident or
unreasonable use, neglect, improper service or other causes not arising out of defects in materials or
construction.  Units which are found to be damaged by abuse resulting in thermally damaged voice coils
are not covered by this warranty but may be replaced at the absolute/sole discretion of Directed. 

ALL

WARRANTIES INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY,
WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE, AND WARRANTY OF
NON-INFRINGEMENT OF INTELLECTUAL PROPERTY ARE EXPRESSLY EXCLUDED TO THE
MAXIMUM EXTENT ALLOWED BY LAW, AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES
ANY PERSON TO ASSUME FOR IT ANY LIABILITY IN CONNECTION WITH THE SALE OF THE
PRODUCT.  DIRECTED HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD
PARTIES INCLUDING ITS AUTHORIZED DEALERS OR INSTALLERS.

Unit must be returned to Directed,

postage pre-paid, with bill of sale or other dated proof of purchase bearing the following information:
consumer's name, telephone number, and address, authorized dealer's name and address, and product
description.  Note: This warranty does not cover labor costs for the removal and reinstallation of the unit.

IN ORDER FOR THIS WARRANTY TO BE VALID, YOUR UNIT MUST BE SHIPPED WITH PROOF OF
INSTALLATION BY AN AUTHORIZED DIRECTED DEALER.  ALL UNITS RECEIVED BY DIRECTED FOR
WARRANTY REPAIR WITHOUT PROOF OF DIRECTED DEALER INSTALLATION WILL BE COVERED
BY THE LIMITED 1 YEAR PARTS AND LABOR WARRANTY.  

Note: This warranty does not cover labor

costs for the removal and reinstallation of the unit. 

BY PURCHASING THIS PRODUCT, THE CONSUMER

AGREES AND CONSENTS THAT ALL DISPUTES BETWEEN THE CONSUMER AND DIRECTED SHALL
BE RESOLVED IN ACCORDANCE WITH CALIFORNIA LAWS IN SAN DIEGO COUNTY, CALIFORNIA.

16

Содержание 245ix



















Отзывы: