4ms Company Dual Looping Delay Скачать руководство пользователя страница 2

Страница: 2 / 20

Table of Contents

Setting up your Looping Delay

1. Power off your Eurorack system.

2. On the back of the

Looping Delay

you will see a 16-pin header labeled “-12V”. The 16-pin header

connects to a Eurorack power header using the included power cable. Connect one end of the

power cable to a Eurorack power header on your power supply distribution board and the other end

to the

Looping Delay

with the red stripe on the power cable oriented towards the bottom of the

module.

3. Using the included screws, securely attach the

Looping Delay

to the rails of your case.

4. Power on your Eurorack system.

Note: The

Looping Delay

is reverse-polarity protected, but incorrectly connecting any module in any

system can damage other modules on the power bus.

Setting up your Looping Delay

..............................................................................2

Basic features:

.......................................................................................................3

Controls and Jacks

................................................................................................3

Infinite Hold vs. 100% Feedback

...........................................................................7

Why do I hear something I played a long time ago?

.............................................7

Signal Routing: Using Send and Return

................................................................8

Advanced Usage

Loop start and stop points: Trimming the loop

......................................................8

Windowing (aka Scrolling or Scrubbing)

................................................................8

Using CV with Windowing

...............................................................................9

Unquantized Time Mode and 1V/Oct CV

..............................................................9

Stereo and Mono Modes

.....................................................................................10

Octave Up/Down When changing Modes

.....................................................10

Memory Clear

......................................................................................................10

Quantized Change Mode

.....................................................................................11

Using the Looping Delay with External Clocks

....................................................11

Patch Ideas

Resonant Delay (Waveguide, Karplus-Strong)

.....................................................12

Basic Resonant Delay

....................................................................................12

Playing Resonance with a keyboard or sequencer

........................................12

Sound on Sound Looping #1: Creating and Removing Layers

...........................12

Peeling off Layers

..........................................................................................13

Sound on Sound Looping #2: External Control

...................................................13

Sound on Sound Looping #3: More External Control

..........................................13

Granular Scrubbing

..............................................................................................14

Special Features

Bus Clock Jumper

...............................................................................................15

System Settings Mode

........................................................................................15

Audio Bootloader

.................................................................................................18

Firmware Version

.................................................................................................18

Hardware Test Mode

............................................................................................19

Factory Reset

.......................................................................................................19

Technical Specifications

......................................................................................19

Page of

Содержание Dual Looping Delay





















Результаты поиска

Содержание Dual Looping Delay

Отзывы:

Похожие инструкции для Dual Looping Delay

Бренды по названию

Популярные бренды

4ms Company Dual Looping Delay, Руководство пользователя

Результаты поиска

Содержание Dual Looping Delay

Отзывы:

Похожие инструкции для Dual Looping Delay

Бренды по названию

Популярные бренды