4ms Company Dual Looping Delay Скачать руководство пользователя страница 15

Страница: 15 / 20

Special Features

Bus Clock Jumper

Bus Clock is a 1:1 clock that runs along the Gate pin of the power system.

Modules such as the 4ms

QCD

RCD

SCM+

PEG

DLD

SWN

, and

MiniPEG

are compatible with the clock bus system. To use the

Looping Delay

on a bus

clock system, install the jumper in one of two positions:

Bus Clock Send:

Connect the jumper on the lower position (“SEND”) to send the master clock

from the

Looping Delay

to the clock bus. The clock will be identical (but

separately buffered) as the signal on the

Clock Out

jack.

It is not recommended

to have more than one device sending on the same clock bus system.

Bus Clock Receive:

Connect the jumper on the upper position (“RECV”) to receive a ping clock from the clock bus. The

signal on the bus clock will be automatically patched to the

Ping

jack. By plugging a cable into the

Ping

jack, the bus clock will be disconnected from the

Looping Delay

Note: When receiving a bus clock, you must stop the external bus clock or patch a dummy cable into

the

Ping

jack in order to use the

Ping

tap button.

Bus Clock Disabled:

Remove the jumper completely to disable clock bus support. This is the factory-default. It’s safe to

connect the jumper to only one pin.

System Settings Mode

System Settings Mode

allows you to change the way some features of the

Looping Delay

behave. For

novice users, these are not necessary to modify, but advanced users may wish to explore.

It's recommended that new users get familiar with the

Looping Delay

operation using default system

settings before making changes!

In order to enter or exit

System Settings Mode,

the

Time

switch must be flipped up.

To enter, flip the

Time

switch up and hold down all three buttons for two seconds. Release the buttons

when you see all the buttons’ lights turn off.

There are two ways to exit

System Settings Mode:

1) Exiting while temporarily saving changes is similar to the process of entering

System Settings

Mode

. Flip the

Time

switch up and briefly press all three buttons. Make sure to release the buttons

within 2 seconds or less. The changes you made will stay in effect until you power the module down.

The next time you power it up, the previous settings will be restored.

2) To exit while permanently saving changes, turn the

Time

switch up and hold down all three buttons

for 2 seconds. The

Reverse

and

Inf. Hold

button lights will flash rapidly to confirm saving. Settings will

be saved even after powering down.

Page of

Содержание Dual Looping Delay





















Результаты поиска

Содержание Dual Looping Delay

Отзывы:

Похожие инструкции для Dual Looping Delay

Бренды по названию

Популярные бренды

4ms Company Dual Looping Delay, Руководство пользователя

Результаты поиска

Содержание Dual Looping Delay

Отзывы:

Похожие инструкции для Dual Looping Delay

Бренды по названию

Популярные бренды