3onedata IES716-2GS Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 54

3onedata IES716-2GS Скачать руководство пользователя страница 42

User manual

Page 42

（

Figure 6.8.1

）

Read Community

Use a character string to name a SNMP community. This community only has Get privilege.

Read/Write Community

Use a character string to name a SNMP community. This community has Get and Set privilege.

SNMP TRAP Gateway

IP address of the receiver of the alarm information sent Agent

The device supports warm start of Trap. If existed IP address in Trap gateway, click "Apply", the Trap receiver can

get the trap information. If the trap receiver cannot get trap information, please check network setting and

connecting. Please pay attention to the privilege of Read and Write in SNMP Explorer.

6.8.2 Relay Alarm

Warning had 2 type: Power alarm, port alarm. Main function: once the devices were in unusual status,

can inform administrator in time and repair the status of device quickly, can avoid more lose

Relay warning input type: Close/Open. Once select Close, the light will be bright when have

alarm. Relay will be in open status.

Power alarm

IES716-2GS series provided dual DC power supply (AC power supply did not have alarm), if

one power supply had problem, another will support power supply immediately, dual power supply

hot back-up. Select to enable power alarm, If power supply was in unusual status, device will send

alarm signal, inform power supply work unusual.

Port Alarm

Alarm when port disconnect. Enable port alarm, if port was in unusual status(Connect or

disconnect), device will output a signal, inform the device work unusual.

«
...
40
41
42
43
44
...
»

Содержание IES716-2GS























































Отзывы:

Нет отзывов