3onedata IES716-2GS Скачать руководство пользователя страница 20

Страница: 20 / 54

User manual

Page 20

Broadcast, Multicast or

unicast frames

Broadcast&Multicast only

Broadcast only

The ingress rate is related to CoS priority. Priority Queue is based on QoS setting (the same as

QoS assorted setting includes checking CoS priority), or ingress rate will be based on default. CoS

priority includes 4 queues: Low

，

Normal

，

Medium

，

High.

Operation method:

1. Choice 2 port at first, for example open the COS priority of port 4 and port 5, please according to

6.5 part

2. Then set port 4’s CoS is High, port 5’s CoS is LOW in COS mapping setting interface

3. Last, set the type of limit package and bandwidth of priority queue in Ingress bandwidth

configuration

For example, keep up step 1 and 2, choice “All frame” in port 4 and 5 at step 3. Set 2M in all low

priority queue

：

If priority queue bandwidth configuration is available, must mark the enter into port’s data pack as CoS.

6.4 L2 Features
6.4.1 VLAN

IES716-2GS supports based on 802.1Q VLAN. It deals with messages based on Tag of recognized

message

（

including 802.1p priority and VLAN ID, etc.

）

Frames with 802.1q add 4 byte Tag based on Ethernet frames, including 2 byte TPID, 3 byte

Priority, 1 byte CFI and 12 byte VLAN ID.

TPID:

a 16-bit field set to a value of 0x8100 in order to identify the frame as an IEEE 802.1Q-tagged

frame.

Priority:

It indicates the frame priority level. Values are from 0 (best effort) to 7 (highest); 1 represents

the lowest priority.

CFI:

a 1-bit field. If the value of this field is 1, the MAC address is in non-canonical format. If the value is

0, the MAC address is in canonical format.

VLAN ID:

a 12-bit field specifying the VLAN to which the frame belongs. The hexadecimal values of

0x000 and 0xFFF are reserved. All other values may be used as VLAN identifiers, allowing up to 4,094

VLAN.

1. The type of port’s Line

IES716-2GS series support 2 type port line:

Access:

Port belongs to 1 VLAN, normally, it used for connecting user device, default all port is access

port.

Trunk:

Port belongs to some VLAN, can transmit and receive some VLAN message, normally, it used

for connection of network device.

Содержание IES716-2GS























































Результаты поиска

Содержание IES716-2GS

Отзывы:

3onedata IES716-2GS, Руководство пользователя, Страница: 20 / 54

Результаты поиска

Содержание IES716-2GS

Отзывы: