3M X56 Скачать руководство пользователя

Страница: 90 / 104

3M™ Digital Projector X56

Maintenance

Lamp warning

Replacing the lamp (continued)

HIGH VOLTAGE

HIGH TEMPERATURE

HIGH PRESSURE

►The projector uses a high-pressure mercury glass lamp. The lamp

can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or

worn over time. Note that each lamp has a different lifetime, and some may burst or

burn out soon after you start using them. In addition, if the bulb bursts, it is possible

for shards of glass to fly into the lamp housing, and for gas containing mercury and

dust containing fine particles of glass to escape from the projector’s vent holes.

►

About disposal of a lamp:

This product contains a mercury lamp; do not put

it in a trash. Dispose of it in accordance with environmental laws.

• For lamp recycling, go to www.lamprecycle.org (in the US).

• For product disposal, consult your local government agency

or www.eiae.org (in the US) or www.epsc.ca (in Canada).

For more information, call your dealer.

WARNING

• If the lamp should break (it will make a loud bang when it does),

unplug the power cord from the outlet, and make sure to request a

replacement lamp from your local dealer. Note that shards of glass

could damage the projector’s internals, or cause injury during handling,

so please do not try to clean the projector or replace the lamp yourself.

• If the lamp should break (it will make a loud bang when it does), ventilate the

room well, and make sure not to inhale the gas or fine particles that come out

from the projector's vent holes, and not to get them into your eyes or mouth.

• Before replacing the lamp, turn the projector off and unplug the power

cord, then wait at least 45 minutes for the lamp to cool sufficiently.

Handling the lamp while hot can cause burns, as well as damaging the lamp.
• Never unscrew except the appointed (marked by an arrow) screws.

• Do not open the lamp door while the projector is suspended from

a ceiling. This is dangerous, since if the lamp’s bulb has broken, the

shards will fall out when the cover is opened. In addition, working in

high places is dangerous, so ask your local dealer to have the lamp

replaced even if the bulb is not broken.

• Do not use the projector with the lamp door removed. At the lamp

replacing, make sure that the screws are screwed in firmly. Loose

screws could result in damage or injury.
• Use only the lamp of the specified type. Use of a lamp that does not

meet the lamp specifications for this model could cause a fire, damage or

shorten the life of this product.

• If the lamp breaks soon after the first time it is used, it is possible

that there are electrical problems elsewhere besides the lamp. If this

happens, consult your local dealer or a service representative.

• Handle with care: jolting or scratching could cause the lamp bulb to burst during use.

• Using the lamp for long periods of time, could reduce output, cause it not to light

up or to burst. When the pictures appear dark, or when the color tone is poor, please

replace the lamp as soon as possible. Do not use old (used) lamps; this is a cause of

breakage.

Disconnect

the plug

from the

power

outlet

Содержание X56









































































































Результаты поиска

Содержание X56

Отзывы:

Похожие инструкции для X56

Бренды по названию

Популярные бренды

3M X56, Руководство оператора

Результаты поиска

Содержание X56

Отзывы:

Похожие инструкции для X56

Бренды по названию

Популярные бренды