3M Touch Screen USB Resistive Controller SC500 страница 30 Скачать руководство пользователя

Страница: 30 / 31

SC500 USB Controller Reference Guide

3M Touch Systems Proprietary Information

Technical Specifications

Physical Dimensions

Uncased 2.85 in. x 1.3 in. x 0.45 in. (72.4 mm x 33.0 mm x 11.4 mm)

Board Level Functions

Power 5 VDC (15 mA typical, 28 mA touching);

5% regulation

50 mV maximum ripple and noise

Regulatory Requirements

CE Compliance

Compliant

EMC Emissions – EN 55022:1998

Compliant

EMC Immunity – EN 55024:1998

Compliant

ESD Susceptibility – IEC 61000-4-2

Compliant

EMI Immunity – IEC 61000-4-3

Compliant

Burst Immunity – IEC 1000-4-4

Compliant

FCC Class B / CISPR22 Class B

Compliant

VCCI Class B ITE Emissions (Japan)

Compliant

AS/NZS 3548:1995/CISPR 22 Class B ITE Emissions (Aus.)

Compliant

UL/cUL

Compliant

Ambient Operating and Storage Environmental Conditions

Note:

All humidity is non-condensing

Operating Temperature Range

C to +65

Operating Humidity Range (0 to 95% RH up to +36

C; above 36

C refer to Figure 4 below)

Storage Temperature Range

-20

C to +75

Storage Humidity Range (0 to 80% RH up to +36

C; above 36

C refer to Figure 4

below)

Performance and Reliability

Minimum Touch Duration

1 ms

Touch Resolution

1024 x 1024

(Maximum number of addressable coordinates generated by the controller)
ESD Susceptibility

±8KV Contact Discharge– Class 2 per section 9 of IEC 61000-4-2

Compliant

1 false touch allowed
±20KV Air Discharge – Class 1 per section 9 of IEC 61000-4-2

Compliant

Normal Operation – No false touches
MTBF (by MIL Std. 217F Calculation)

>400,000 Hours

ESD discharges to a 3M Touch Systems touch screen connected to the controller

Содержание Touch Screen USB Resistive Controller SC500
































Результаты поиска

Содержание Touch Screen USB Resistive Controller SC500

Отзывы:

Похожие инструкции для Touch Screen USB Resistive Controller SC500

Бренды по названию

Популярные бренды

3M Touch Screen USB Resistive Controller SC500, Справочное руководство

Результаты поиска

Содержание Touch Screen USB Resistive Controller SC500

Отзывы:

Похожие инструкции для Touch Screen USB Resistive Controller SC500

Бренды по названию

Популярные бренды