3M SST Скачать руководство пользователя страница 42

Страница: 42 / 90

32 • Ch. 3 Burster Mechanism

75-0302-1450-8, Version 1

SST Transport and Burster Mechanism Manual

Note:

The Single Infeed Burster automatically draws up the tickets.

3. Carefully feed the ticket into the ticket infeed slot and into the bottom roller. About 1-20

seconds after the first light sensor (LS 4) is activated and you feel the tickets “kick-back”

when you push them in place, the Burster automatically draws up the tickets.

Warning! Make sure that the ticket is straight. If the ticket is slanted, a ticket jam may

occur.

Note:

If the Burster does not draw up tickets, verify that you have SST CPU software 3.6.0 or

greater and that DIP Switches #4 and #5 on DIP Switch Bank S1 of the SST CPU Board

Figure 3.12

Inserting a Ticket into Single-Infeed Burster

Infeed Slot

Bottom Roller

Light Sensor 4

Ticket

Mag Stripe

Содержание SST



























































































Результаты поиска

Содержание SST

Отзывы:

Похожие инструкции для SST

Бренды по названию

Популярные бренды

3M SST, Руководство пользователя

Результаты поиска

Содержание SST

Отзывы:

Похожие инструкции для SST

Бренды по названию

Популярные бренды