3M SST Скачать руководство пользователя страница 37

Страница: 37 / 90

SST Transport and Burster Mechanism Manual

75-0302-1450-8, Version 1

Ch. 3 Burster Mechanism • 27

3. With the securing knob and Burster serial number label facing you, align the Burster frame

between the support clips on the back of the SST Transport.

Warning! Before hanging the Burster on the SST Transport, make sure that the Burster

Protector is in place. The Burster Protector slides down between the sensors

behind the Burster CPU Board. The Burster Protector channel rests on top of the

Burster CPU Board. If you do not use the Burster Protector, you may damage the

unit.

4. Slide the Burster forward until the Burster securing knob and the inside screw are aligned

with the notch on the SST Transport Burster Support. Make sure the Burster is flush

against the back of the SST Transport. Figure 3.7 illustrates the SST/HP-1 Transport

aligned with a Burster. Figure 3.8 illustrates the SST/HP-4 Transport aligned with a

Burster.

Figure 3.6

Location of Securing Knob on Single-Infeed SST Ticket Burster

Securing Knob

Содержание SST



























































































Результаты поиска

Содержание SST

Отзывы:

Похожие инструкции для SST

Бренды по названию

Популярные бренды

3M SST, Руководство пользователя

Результаты поиска

Содержание SST

Отзывы:

Похожие инструкции для SST

Бренды по названию

Популярные бренды