manualshive.com logo in svg

3M SCOTT PAK-ALERT, Инструкция по эксплуатации и обслуживанию, Страница: 15 / 24

Поделиться
Скачать
3M SCOTT PAK-ALERT Скачать руководство пользователя страница 15

Page 15 of 24

P/N 595370-01 Rev B   07/19

NOTE

IF THE LOW BATTERY INDICATION (ONE STEADY CHIRP EVERY 

TWO (2) SECONDS WITH NO FLASHING LIGHTS) OCCURS AT ANY 

TIME DURING REGULAR OPERATIONAL INSPECTION, DO NOT USE 

THE SCBA. CHANGE THE BATTERIES IN THE SENSOR MODULE 

IMMEDIATELY AND REPEAT THE REGULAR OPERATIONAL TEST 

OR TAKE THE SCBA OUT OF SERVICE UNTIL THE BATTERIES ARE 

CHANGED AND THE REGULAR OPERATIONAL TEST IS SUCCESSFULLY 

PERFORMED.

WARNING

IF THE LOW BATTERY INDICATION (ONE 

STEADY CHIRP EVERY TWO (2) SECONDS 

WITH NO FLASHING LIGHTS) OCCURS AT 

ANY TIME DURING REGULAR OPERATIONAL 

INSPECTION, DO NOT USE THE SCBA. CHANGE 

THE BATTERIES IN THE SENSOR MODULE 

IMMEDIATELY AND REPEAT THE REGULAR 

OPERATIONAL TEST OR TAKE THE SCBA 

OUT OF SERVICE UNTIL THE BATTERIES ARE 

CHANGED AND THE REGULAR OPERATIONAL 

TEST IS SUCCESSFULLY PERFORMED. 

FAILURE TO REPLACE THE BATTERIES AND/

OR CONTINUING WITH MULTIPLE USES OF THE 

SCBA AFTER THE LOW BATTERY CONDITION 

HAS BEEN INDICATED BY THE DISTRESS 

ALARM MAY RESULT IN FAILURE OF THE 

DISTRESS ALARM DURING USE AND POSSIBLE 

INJURY OR DEATH OF THE USER.

When performing the REGULAR OPERATIONAL INSPECTION, verify that 

the Sensor Module lights are operating as described below:

OPERATION OF SENSOR MODULE LIGHTS

NOTE

THE YELLOW LIGHT IS A COMBINATION OF THE RED, GREEN, AND 

WHITE LIGHTS THAT APPEARS YELLOW-ORANGE OR AMBER FROM 

A DISTANCE. AT CLOSE RANGE THE INDIVIDUAL LIGHTS MAY BE 

VISIBLE.

ACTION OR SITUATION

BEHAVIOR OF LIGHTS

Start Air-Pak SCBA (i.e., open cylinder valve)

Bright light, then flashing green light

Normal operation

Flashing green light

Air cylinder between 1/2 and 1/3 full

Flashing yellow light (2 quick flashes) every second

Air cylinder less than 1/3 full (low air)

Flashing yellow light (alternately)

Low battery while unit is on

Flashing yellow light once every 2 seconds

Shut down

Off

Press reset button on control console with unit off (battery 

test)

Good battery: Bright light, then flashing green light
Low battery: Bright light, then flashing red light

Press manual alarm button on control console with unit off Flashing red light (simultaneously)
Press reset button on control console during full alarm

Flashing green light

PASS pre-alarm

Flashing red light (alternately)

PASS full alarm

Flashing red light (simultaneously)

Содержание SCOTT PAK-ALERT

























Отзывы:

Нет отзывов