background image

  

Operations and Instruction Manual 

Model #4075 

Portable Concrete Anchorage Connector 

ANSI Z359.1-07  5,000 lbs / 22kn 

OHSA 1910.66 & 1926.502

 

Effective: 01/2012   Expires: 01/2022   IM-0049 REVA 

1. 

Follow all manufacturer’s instructions. 

2. 

Do not use incompatible connectors. 

3. 

Always inspect your units prior to use. 

4. 

Use the proper method of coupling to anchorage. 

5. 

Remove unit for service if a fall has occurred.  

6. 

Patch all holes with concrete when job is complete. 

7. 

For use by one person only. 

8. 

Pregnant women and minors must not use this product. 

9. 

Designed safe working load is 400 LBS (149.3 kg). Do not  

        exceed this weight. 
10.   Not for use with horizontal lifeline systems.  Refer to item #4077.

 

Model #4075 SafeClaw 3/4” anchor is to be used in concrete substrate only.  

DO NOT use in steel, wood or any other substrate.   

 

This product is designed for use in cured concrete only and may be pulled in all directions up to 90. 

 

SafeClaw Fall Protection Anchor can be placed in: 

 

* Horizontal surfaces 

* Vertical surfaces 

* Overhead / ceiling surfaces 

*** Warning *** 

Do not use incompatible connectors with any SafeClaw Anchor.  

Refer to separate instructions supplied with your anchorage connector. 

Spoon 

End Termination 

Bushing Guide 

Stop Sleeve 

Trigger 

Spring Swage 

Anchor Loop 

Heavy Duty Return Wire 

3/4” SafeClaw Anchorage Connectors 

3/4” SafeClaw

 

 Fall Protection Anchor 

 



Model  -  #4075 



Designed safe working load: 400 lbs. 



Tested  -  ANSI Z359.1-2007 



OSHA  -  1910.66 & 1926.502 



Strength  -  5,000 lbs / 22kn 



Color coded in orange tubing 

IMPORTANT 

All persons using this equipment must read and understand all instructions. Failure to do so may result in serious injury or 
death. If a fall occurs, the SafeClaw anchor must be disposed of according to the manufacturer instruction. Users should be 

familiar with pertinent regulations governing this equipment. All individuals who use this product must be correctly 

instructed on how to use this device.  

Содержание 4075








Отзывы: