SAFETY INFORMATION
Read, understand, and follow all safety information contained in these instructions prior to installation and use of the 3M™ Series Iron Reduction Filtration System 3MAPPM
Series. Retain these instructions for future reference. Failure to follow installation, operation and maintenance instructions may result in property damage and will void war-
ranty.
This product includes a GAST
®
component. Please refer to GAST website at www.gastmfg.com for detailed information on GAST LOA-P109-AA compressor or
contact your Dealer/Installer or our Customer Care Team at 855-3M-WATER (855-369-2837).
Intended use:
The 3M™ Series Iron Reduction Filtration System 3MAPPM Series is intended for use in reducing iron in water in homes and has not been evaluated for other uses.
The system must be installed indoors near the point of entry of a home water line, and be installed by qualified professional installers according to these installation
instructions.
EXPLANATION OF SIGNAL WORD CONSEQUENCES
WARNING
Indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury and/or property damage.
CAUTION
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury and/or property damage.
CAUTION
Indicates a potentially hazardous situation, which, if not avoided, may result in property damage.
WARNING
To reduce the risk associated with choking:
•
Do not
allow children under 3 years of age to have access to small parts during the installation of this product.
To reduce the risk associated with ingestion of contaminants:
•
Do not
use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system.
To reduce the risk of physical injury:
• Shut off inlet water supply and depressurize system as shown in manual prior to service.
• Do not operate system with air release valve (ARVTA-1X) in the closed position.
To reduce the risk associated with a hazardous voltage:
• If the home electrical system requires use of the cold water system as an electrical safety ground, a jumper must be used to ensure a sufficient ground connection across the
filter installation piping — refer installation to qualified personnel.
• Do not use the system if the power cord is damaged — contact qualified service personnel for repair.
To reduce the risk associated with back strain due to the heavy weight of the various system components:
• Follow safe lifting procedures.
CAUTION
To reduce the risk associated skin, eye, and respiratory tract irritation from gravel and filter media during installation:
• Gravel and several types of filter media may be used in this product, depending upon the application. During installation, dust may cause irritation to skin, eyes, and respiratory tract.
• Utilize a NIOSH-approved dust filter mask, protective gloves, and appropriate eye protection when handling and pouring gravel and filter media.
• To request an MSDS relating to this product, call 203-238-8965 or go to www.3M.com, select country, and use the search engine to search MSDS. For emergencies, call
800-364-3577 or 651-737-6501 (24 hours).
CAUTION
To reduce the risk associated with property damage due to water leakage:
•
Read and follow
Use instructions before installation and use of this water treatment system.
• Installation and use
MUST
comply with existing state or local plumbing codes.
•
Protect from freezing
, relieve pressure and drain system when temperatures are expected to drop below 33°F (0.6°C).
•
Do not
install on hot water supply lines. The maximum operating water temperature of this filter system is 110°F (43.3°C).
•
Do not
install if water pressure exceeds 50 psi. If your water pressure exceeds 50 psi (345 kPa), you must install a pressure limiting valve. Contact a plumbing professional
if you are uncertain how to check your water pressure.
•
Do not
install where water hammer conditions may occur. If water hammer conditions exist you must install a water hammer arrester. Contact a plumbing professional if
you are uncertain how to check for this condition.
• Where a backflow prevention device is installed on a water system, a device for controlling pressure due to thermal expansion must be installed.
•
Do not
use a torch or other high temperature sources near filter system, cartridges, plastic fittings or plastic plumbing.
• On plastic fittings, never use pipe sealant or pipe dope.
Use PTFE thread tape only,
pipe dope properties may deteriorate plastic.
• Take care when using pliers or pipe wrenches to tighten plastic fittings, as damage may occur if over tightening occurs.
•
Do not
install in direct sunlight or outdoors.
• Install system in such a position as to prevent it from being struck by other items used in the area of installation.
• Ensure all tubing and fittings are secure and free of leaks.
•
SHUT OFF FUEL OR ELECTRIC POWER SUPPLY TO WATER HEATER
after water is shut off.
•
Do not
install system where water lines could be subjected to vacuum conditions without appropriate measures for vacuum prevention.
•
Do not
apply heat to any fitting connected to bypass or control valve as damage may result to internal parts or connecting adapters.
To reduce the risk associated with property damage due to plugged water lines:
• Pay particular attention to correct orientation of control valve. Water flow should match arrow on control valve. The Inlet and Outlet of other water treatment equipment
products will vary depending on the control valve brand used.
IMPORTANT NOTES
•
Failure to follow instructions will void warranty.
