3E THERMOSALD ISC Скачать руководство пользователя | Manualshive

Страница: 12 / 20

background image

THERMOSALD ISC – MANUAL QUICK START

Rev. 2010 / 03

Manual cod.: 3ES080x_V5.1_QS_EN Page Nr. 12 Tot. Nr . 20
Includes all previous models

NOTE – If calibration problems arise, perform a MASTER RESET procedure starting from stage 5.
               To perform a MASTER RESET procedure, use either of the two modes below:
               mode 1 – Keep the ARROW DOWN + ARROW UP buttons pressed for 6 seconds.
               mode 2 - Keep the external RESET+CALIBRATION buttons pressed for 6 seconds.
               The four LEDS on the equipment stay on  for 3 seconds

4.4 - PUTTING THE SYSTEM INTO SERVICE – BASIC SETUP + MULTI-LINGUAL PANEL +
POTENTIOMETERS (+RS485 OPTION)

NOTE 1: Perforn the same operations as those described in paragraph 4.3 above.
NOTE 2: To enable the potentiometers, change the MACHINE DATA items = 1, Potentio display.
NOTE 3: Set the maximum pre-heat and heat-seal temperatures by using the control panel. To step them down, adjust the
analog inputs (for resolution see technical note paragraph 4.1).

PRE-HEAT POTENT.

HEAT-SEAL POTENT.

CLEAR FAULTS/ RESET
BUTTON

CALIBRATION BUTTON

«
...
10
11
12
13
14
...
»

Содержание THERMOSALD ISC





















Отзывы:

Нет отзывов

Похожие инструкции для THERMOSALD ISC

Бренд: K&K Страницы: 6

Бренд: ABC Design Страницы: 38

Бренд: easydriver Страницы: 26

Бренд: Calsense Страницы: 10

Бренд: ABC Design Страницы: 10

Бренд: ABC Design Страницы: 10

Бренд: Coccolle Страницы: 11

Бренд: Watlow Страницы: 20

Бренд: Leggett & Platt Страницы: 20

ELEMENTAIR B-MARK I

Бренд: Xvent Страницы: 9

Бренд: Bartec Страницы: 52

Multilin GEK-113328A

Бренд: GE Страницы: 218

Бренд: Traxxas Страницы: 44

Бренд: Ayra Страницы: 19

Бренд: Lumel Страницы: 20

Бренд: Flamingo Страницы: 20

Бренд: nurse Страницы: 16

Бренд: LAE electronic Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды