manualshive.com logo in svg

3Com 8800 SERIES, Руководство по настройке

Серия продуктов 3Com 8800 SERIES предлагает ряд решений для сетей. Установочное руководство доступно для загрузки бесплатно на manualshive.com. Получите все необходимые инструкции для установки и настройки вашего устройства, чтобы обеспечить эффективную работу вашей сети.

Поделиться
Скачать
background image

3Com Switch 8800 Configuration Guide 

Chapter 12  ARP Configuration

 

12-1 

Chapter 12  ARP Configuration 

12.1  Introduction to ARP 

Address Resolution Protocol (ARP) is used to resolve an IP address into a MAC 

address. 

I. Necessity of ARP 

An IP address cannot be directly used for communication between network devices 

because network devices can only identify MAC addresses. An IP address is only an 

address of a host in the network layer. To send the data packets transmitted through the 

network layer to the destination host, MAC address of the host is required. So the IP 

address must be resolved into a MAC address. 

II. ARP implementation procedure 

When two hosts on the Ethernet need to communicate with each other, they must know 

the MAC addresses of each other. Every host maintains the IP-MAC address 

translation table, which is known as the ARP mapping table. A series of maps between 

IP addresses and MAC addresses of other hosts which recently communicate with the 

local host are stored in the ARP mapping table. When a dynamic ARP mapping entry is 

not in use for a specified period of time, the host removes it from the ARP mapping 

table so as to save the memory space and shorten the interval for the switch to search 

ARP mapping table. 

Suppose there are two hosts on the same network segment: Host A and Host B. The IP 

address of Host A is IP_A and the IP address of Host B is IP_B. Host A will transmit 

messages to Host B. Host A checks its own ARP mapping table first to know whether 

there are corresponding ARP entries of IP_B in the table. If the corresponding MAC 

address is found, Host A uses the MAC address in the ARP mapping table to 

encapsulate the IP packet in frame and sends it to Host B. If the corresponding MAC 

address is not found, Host A stores the IP packet in the queue waiting for transmission, 

create an ARP request packet and broadcast it throughout the Ethernet. The ARP 

request packet contains the IP address of Host B and IP address and MAC address of 

Host A. Since the ARP request packet is broadcasted, all hosts on the network 

segment can receive the request. However, only the requested host (namely, Host B) 

needs to process the request. Host B first stores the IP address and the MAC address 

of the request sender (Host A) in the ARP request packet in its own ARP mapping table.  

Then, Host B generates an ARP reply packet by adding its own MAC address into the 

packet, and then send it to Host A. The reply packet is directly sent to Host A in stead of 

being broadcasted. Receiving the reply packet, Host A extracts the IP address and the 

Содержание 8800 SERIES






































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 8800 SERIES

D-Linke DHP-346AV Quick Installation Manual preview
DHP-346AV
Бренд: D-Linke Страницы: 32
Abocom FW200 Specifications preview
FW200
Бренд: Abocom Страницы: 1
Keithley 7707 User Manual preview
7707
Бренд: Keithley Страницы: 59
Lindy 25046 User Manual preview
25046
Бренд: Lindy Страницы: 4
Paradyne Hotwire 5100 User Manual preview
Hotwire 5100
Бренд: Paradyne Страницы: 45
QNAP TS-130-US User Manual preview
TS-130-US
Бренд: QNAP Страницы: 39
Speedtouch IPQoS Configuration Manual preview
IPQoS
Бренд: Speedtouch Страницы: 124
Kohler Mira Pixel User Manual preview
Mira Pixel
Бренд: Kohler Страницы: 32
Ubiquiti EdgeSwtch 5XP Quick Start Manual preview
EdgeSwtch 5XP
Бренд: Ubiquiti Страницы: 13
TP-Link VIGI NVR1004H-4P Quick Installation Manual preview
VIGI NVR1004H-4P
Бренд: TP-Link Страницы: 2
Tripp Lite N310-30M Specification Sheet preview
N310-30M
Бренд: Tripp Lite Страницы: 2
H3C SecPath F1070 Manual preview
SecPath F1070
Бренд: H3C Страницы: 68
Rackable Systems OmniStor 4900F Series User Manual preview
OmniStor 4900F Series
Бренд: Rackable Systems Страницы: 196
Chaparral FS1310 User Manual preview
FS1310
Бренд: Chaparral Страницы: 96
Aaeon FWS-7811 Manual preview
FWS-7811
Бренд: Aaeon Страницы: 100
ZyXEL Communications P-660R-F1 series User Manual preview
P-660R-F1 series
Бренд: ZyXEL Communications Страницы: 268
X-Micro XWL-11GPAR User Manual preview
XWL-11GPAR
Бренд: X-Micro Страницы: 24
Billion BiPAC 7560G Specifications preview
BiPAC 7560G
Бренд: Billion Страницы: 2

Бренды по названию

Популярные бренды

Загрузить еще бренды