manualshive.com logo in svg

2N Helios IP, Руководство по настройке

Поделиться
Скачать
2N Helios IP Скачать руководство пользователя страница 100

2N TELEKOMUNIKACE a.s., www.2n.cz

100/177

SIP Proxy – is an IP network server responsible for call routing (call transfer to 
another  entity  closer  to  the  destination).  There  can  be  one  or  more  SIP  Proxy 
units between the users.

SIP  Registrar  –  is  an  IP  network  server  responsible  for  user  registration  in  a 
certain network section. As a rule, SIP device registration is necessary for a user 
to be accessible to the others on a certain phone number. SIP Registrar and SIP 
Proxy are often installed on one and the same server.

RTP 

 – is a protocol defining the standard packet 

(Real-Time Transport Protocol)

format  for  audio  and  video  transmission  in  IP  networks. 

  uses  the 

2N  Helios  IP

RTP  for  audio  and  video  stream  transmission  during  a  call.  The  stream 
parameters  (port  numbers,  protocols  and  codecs)  are  defined  and  negotiated 
via the SDP (Session Description Protocol).

The 

 intercoms support three ways of SIP signalling:

2N  Helios IP

®

via  the 

  (

),  which  is  the  most  frequently  used 

User  Datagram  Protocol

UDP

unsecured signalling method

via  the 

 

,  which  is  less  frequent,  yet 

Transmission  Control  Protocol  ( TCP)

recommended unsecured signalling method

via  the 

  protocol,  where  SIP  messages  are 

Transaction  Layer  Security  (TLS)

secured against third party monitoring and modification

List of Parameters

The 

 Phone settings are arranged in five tabs:

2N Helios IP

SIP 1 and SIP 2 – complete SIP terminal settings

Calls – incoming and outgoing call settings

Audio  –  audio  codec,  DTMF  transmission  and  other  audio  stream  transmission 
settings

Video  –  video  codec,  video  resolution  and  other  video  stream  transmission 
settings

SIP 1 and SIP 2

The  2N   Helios  IP  intercoms  allow  two  independent  SIP  accounts  (SIP  1  and  SIP  2 

®

tabs)  to  be  configured.  Thus,  the  intercom  can  be  registered  under  two  phone 

numbers, with two different SIP exchanges and so on. Both the SIP accounts process 

incoming calls equivalently. Outgoing calls are primarily processed by account 1, or, if 

by account 2. Select the 

account 1 is not registered (due to SIP exchange error, e.g.), 

account number for the phone numbers included in the phone directory to specify the 

account to be used for outgoing calls (example: 2568/1 - calls to number 2568 go via 

account 1, sip:[email protected] calls to sip uri via account 2).

Содержание Helios IP


















































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды