background image

1

 

MT-8000 series 

MT-8104iH 

Installation Instruction 

 
 
 

1.0 Installation and Startup Guide   

Install Environment 

 

Where  
Used

 

The MT-600/8000 Series is designed for industrial. The temperature range of operating 
is from 32 to 122 °F (0 to 50 °C), as majority of industrial environments. It may not be 
suitable for using in certain outdoor applications. Please consult the factory for 
advised usage in outdoor applications. 

NEMA 

Rating 

 

The MT-600/8000 Series front bezel is NEMA 4 rated. When installed properly in a 
NEMA 4 panel, the NEMA 4 rating of the panel will not be compromised. This means 
that fluids will not enter the panel during wash downs. 

Electrical 

Environment 

The MT-600/8000 Series has been tested to conform to European CE requirements. 
This means that the circuitry is designed to resist the effects of electrical noise. This 
does not guarantee noise immunity in severe cases.    Proper wire routing and 
grounding will insure proper operation. 

Mechanical 

Environment 

 

 

 

 

Avoid installing units in environments where severe mechanical vibration or shocks 
are present. 

2.0 Installation Instructions 

2.1 Mounting Instructions 

2.1.1 Location Considerations 

Care should be taken when locating equipment behind the unit to ensure that AC power wiring, PLC 

output modules, contactors, starters and relays, and any other source of electrical interference are located 

away from the back of the unit. 

 

Particular note should be taken to the position of variable speed drives and switching power supplies. 

Their input and load cables should be screened to a central star earth point. 

 

2.1.2 Making a NEMA-4 Mounting 

Panel  
Details

 

The unit can be mounted into panels with a depth of 4”(105mm).    It is recommended that 
the unit be mounted on the front panel of a steel enclosure, through an appropriate 
opening*. Allow a clearance of 1”(25mm) around the sides of the unit for mounting 

                         www.ipc2u.ru

Summary of Contents for MT-600 Series









Reviews: