©2008 Viega
Congratulations on Purchasing the Compact Angled PEX Crimp Hand Tool, a
full-circle crimp tool for PEX tubing. Use the Compact Angled PEX Crimp Hand
Tool to install only manufacturer-approved crimp rings, pipe and fittings.
Important Crimp Tool Instructions: Read Before Using
DO NOT USE THIS TOOL UNLESS YOU CAN EXECUTE A PROPER CRIMP
ACCORDING TO APPROVED METHODS AND RECOGNIZED STANDARDS.
If you cannot complete a proper crimp with your tool (including the ability to apply
enough force to make the tool work correctly) discontinue use of the tool.
With the pipe, fitting, and crimp ring in assembly position:
Pull back on the upper, moving handle and hold both handles closed
with jaws in full open position. (see illustration)
Position jaws around the crimp ring.
Gently release hand pressure on the moving handle to let the jaws close
properly and squarely over the crimp ring.
Firmly press the handles together to complete the crimp.
DO NOT CRIMP TWICE.
Pull back on the moving handle to release the tool from the crimp ring.
Operating Instructions:
1
1
2
2
3
3
4
4
5
5
• Completed crimps must meet the dimensional requirements of
ASTM F1807, F2159, F845 or F1380 fitting standards.
• Check each crimped ring with the Crimp Caliper (Viega stock code 53507) or
other suitable measuring device.
• DO NOT make the measurement at the scared (jaw overlap point) portion of the ring.
• If the GO side does NOT fit over the ring, it is under crimped. The connection
must be cut out, the fitting replaced and new crimp rings used. The tool must be
adjusted before proceeding.
• If the NO GO side fits over the ring, it is OVER crimped. The connection must be
cut out, the fittings replaced and new crimp rings used. The tool must be adjusted
before proceeding. See “Tool Adjustment Procedures”.
• Refer to the fitting and tubing manufacturer’s product assembly instructions for the
correct procedure for joining and gauging.
• The dimensional accuracy of the Crimp Caliper can be affected by normal
field wear and tear. Therefore, it is recommended you check it with a suitable
measuring device or change to a new gauge regularly to ensure measurement
accuracy.
• The Compact Angled PEX Crimp Hand Tool is user adjustable. When the tool
makes unsatisfactory crimps it must be adjusted.
• The Compact Angled PEX Crimp Hand Tool must be checked for correct
adjustment at the start of every day. Each crimp ring shall be gauged to ensure
that it has been crimped properly and for the accuracy of the tool.
Nominal
Tube Size
Minimum
Maximum
3/8"
0.580"
0.595"
1/2"
0.700"
0.715"
3/4"
0.945"
0.960"
1"
1.175"
1.190"
Dimensions of crimp ring after a proper, single crimp:
The maximum out-of-roundness of a
completed crimp shall not exceed .006".
This is the difference between the minimum
outside diameter of a properly crimped ring
and the maximum outside diameter of the
same properly crimped ring.
The Compact Angled PEX Crimp Hand Tool handles do not open
like pliers. Forcing the handles apart could cause tool failure.
Use this tool to crimp only copper crimp rings made to ATSM
F1807, F2159, and brass, copper, or plastic fittings for ASTM
F876/F877 SDR9 PEX tubing. Tool may also be used to make
crimp connections with PB tubing and appropriate rings and
fittings.
Maintenance Instructions:
Tool maintenance can effect the life of your Compact Angled PEX Crimp Hand Tool
and the quality of the tool’s crimp. Lubricate the pivot points frequently with light oil
to ensure smooth action and maximum tool life.
DO NOT ATTEMPT TO REPAIR THE TOOL. FOR TOOL INFORMATION, CALL
VIEGA, AT 800.775.5039.
IMPORTANT:
The Compact Angled PEX Crimp Hand Tool is under limited warranty
for ninety days from date of purchase. To ensure warranty availability, fill out the
information on the reverse side and retain with a dated proof of purchase. Please
include a copy of your proof of purchase when returning your tool for any adjustment
or repair covered under warranty.
TEL 800-VIEGA-NA • FAX 800-976-9817
www.viega.com
Compact Angled PEX
Crimp Hand Tool
PI-PF-41703 5/08
