gsm-r5-zas_user_manual en v2-06
strana 1 / 5
GSM-R5-ZAS, GSM-R5-ZAS-xxx
1.
Introduction
The GSM-R5-ZAS (hereinafter referred to as
GSM relay
5
) is relay controlled remotely
by SMS messages over GSM network. Other features include, for example, remote
temperature control,
„
ring-out
“
control of the appliance, or an additional input for event
and alarm reporting. The device remembers its status and parameters, so
it doesn’t
have to be setup after every power-on.
GSM relay
5
is equipped with a removable
terminal block located on the side of the device designed to connect one analog input
for temperature or logic value measurement.
GSM relay
5
is tailored for easy
connection, installation and control. It is connected to the existing power supply of the
appliance. This supply can then be switched on, off, temporarily disconnected or used
to automatically control the heating to the desired temperature. The state of the
connected inputs can be detected by SMS messages or the
GSM relay
5
can be set up
to send SMS messages whenever state of the input is changed. In addition to the basic
version with the terminal block on the side there are also variants with additional
features.
1)
Plug for insertion into the mains 230 V
AC.
2)
Socket 230 V
AC.
for connecting the
controlled device (10 A, 2300 W)
3)
ON/OFF (yellow LED + button)
4)
PWR (green LED for indication of power)
5)
Micro USB for configuration
6)
SIM card holder
7)
Removable terminal for connecting
external temperature sensor (the sensor
must be ordered separately).
8)
GSM (blue LED for indication of
connection to GSM network)
For the basic variation it is possible to
order the connector for the external
antenna GSM-R5-ANT.
9)
For other variants, there is 6pin terminal
form the underside. See chapter
„
Variations with EXTENSIONS
“.
2.
Commercial packaging
1ks GSM relay
5
1ks 2 pin connector, pitch 3,81mm
1ks 6 pin connector, pitch 3,81mm ...only variants with extensions.
1ks Articulated antenna 2dB...............only variants with additional features.
1ks screwdriver 2mm
3.
Recommended accessories
GSM-C-T2 semiconductor temperature sensor in plastic
enclosure, 1m cable.
4.
First time startup
1.
For proper device operation a SIM card is required. The SIM card have to be
functional, activated and with disabled PIN code. Prepaid credit cards must have
nonzero credit.
2.
Insert the card into the Holder
.
Push the card inside, until you hear mechanical
„click“.
3.
Now you can insert the device into the mains. If the socket is OK green LED PWR
will turn on.
4.
Now connect your electrical appliance into the
GSM relay
5
.
5.
First press the button on the
GSM relay
5
. The relay will change its state and yellow
LED ON/OFF should light up.
6.
Send SMS message „1234 OFF“ to the SIM card you’ve inserted into the
GSM
relay
5
. This will turn off the socket and add your telephone number into its list
under name MASTER. The password
1234
can be later changed. The device will
execute …
to anyone with correct password.
7.
???
8.
Test the temperature control, for example at 25° C.
The socket will switch on and
off according to the temperature input
A1
. Connect the temperature sensor to the
temperature input
A1
and send the SMS
1234 TEMP 25
. The control is terminated
by a
1234 OFF
message or by pressing the ON / OFF button.
9.
Factory setting of GSM relay5 can be restored by sending a
1234 !FACTORY
message. If you made a backup configuration of SeaConfigurator settings (Settings
tab -> Files button -> File option), you can restore your settings from this backup
(Settings tab -> Files button -> File option).
10.
The names of the inputs, outputs (their states) and the command names can be
modified according to your ideas using the
SeaConfigurator
configuration
software. This configuration program can be downloaded free of charge from
„
Configurator
“
in the search) and install it on
your PC.
5.
Technical specification
Parameter
Symbol
MIN.
TYP.
MAX.
Unit
Dimensions
Width
W
65
mm
Length
L
140
mm
Depth
D
95
mm
Power Supply
Voltage
PWR
100
230
250
V
AC
.
Consumption
1
3
W
Battery
Li-ION
Operation after power failure
20
hours
Digital outputs
Mains socket - Y2 (switched relay)
Voltage
V
OUT
According to the supply voltage
Max. current -
Resistive load
I
OUT
10
A
Analog input
External (removable) temperature sensor GSM-C-T2
distinction
0,1°C.
accuracy in range 0 to 30
°C … 1
°C
Temperature
measurement
A1
-30
+55
°C
Temperature
Storage
tSTG
-40
+85
°C
Operational
Ta
-20
+40
°C
Humidity
RVmax
90
%
GSM relay
5
is intended for indoor use
!
For basic variant, it is possible to order Li-ION accumulator for reporting of power
failure..... GSM-R5-BAT.
For more specification see chapter
„
Versions with extensions
“.
6.
Hardware
6.1
Connectors
GSM relay5
has a plug, that plugs into the mains and a switched socket for connection
of external appliance. the on / off switching is done by built-in relay.
It is possible to connect one external temperature sensor KTY81-210. The length of the
wires to the connected external temperature sensor is not limited, but it should be
considered that the longer conductor has a certain resistance that affects the measured
value. 16 Ω
equals approximately
1 ° C.
6.2
LED diodes
LED
Color
Meaning
6.3
SIM card holder, button, USB and antenna
Insert SIM Card according to the picture. Push the card inside, until you hear mechanical
„click“.
Press the ON / OFF button briefly to switch on or off the appliance connected in the
socket. If the
GSM relay
5
is not powered and the battery is installed, the
GSM relay
5
switches off by pressing for a long time (>= 5 seconds).
Micro USB connector is for offline configuration with SeaConfigurator.
If the device is equipped with an antenna connector, the antenna is connected via the
SMA connector. The device is fitted with a SMA female connector, the connected
antenna must have a male SMA c
onnector. The impedance is 50 Ω. If there is no
connector, the device is fitted with an internal antenna.
6.4
Battery
GSM relay
5
It can be equipped with a 3.7 V stand-by Li-Ion battery. After power failure,
the device is able to operate in normal mode for about a day (the duration depends on
how much it is used).
7.
Configuration
GSM relay
5
is configured with SeaConfigurator either via the USB connector (microUSB
cable no. HW-11.02) or through the GPRS connection. This configuration program can
be downloaded for free from
„
Configurator
“
) and
install it on your PC.
GSM relay
5
is shipped with a factory configuration that meets the most common
requirements, so it is possible to use the device even without SeaConfigurator. Simply
send the first SMS from the main user's phone number under the
“
First
time startup”
chapter.
Some parameters be changed via SMS, see chapter
„Command List“
.
GSM
Blue
Indicates device status. Possible states are:
Flashing 1:1
…
the device is setting up
Short flash 1x in 4 sec …
device is in operation.
PWR
Green
It is permanently lit when powered from an external
source.
Flashes while running on the internal battery.
ON/OFF
socket (Y2)
Yellow Shines continuously when the socket is switched ON
Before inserting the SIM card into the GSM relay
5
device, you must
first disable the "PIN
code“ !
Insert activated SIM card into any working phone and disable PIN code. In
most mobile phone devices this option is under Settings -> Security.
3
1
2
5
6
7
8
4
