Passcode must be entered with the number keypad lighted up, and
when the light is turned off, press the [*] button and enter it again
then.
When the passcode is incorrectly entered to cancel the input, press
the [ ] button and start from the beginning.
If the passcode is incorrectly entered for five consecutive sounds, a
different alarm sound is played for about 10 seconds, and the
operation of doorlock is paused for roughly 3 minutes. During the
operation pause status, "beep" sound is played every 10 seconds,
and after 3 minutes, a long "beep" sound is played, and the pause
status is automatically disabled.
Convenient Opening of the
Door
Simple operation via card and
passcode
Automatic lock feature
Safer with automatic lock feature
Prank Prevention Feature
In the case of entering unregistered
information, the attempt is
automatically blocked
Dual-Lock Feature
With dual-lock feature, the security
is enhanced
Fire Detection Feature
Built-in fire detection sensor
Crime Prevention Feature
When going out, crime prevention
feature can be used.
Internet Home Page
SamsungSNS(Inc.)
ServiceCenter
Representative
PhoneNumber
Anywhere in the country
If you accurately provide the product name,
fault condition, and contact number, then
we will always provide kind assistance and
quick service to customers' questions.
Precautions for Safety
Warning
Precautions for safety protect the user's safety and prevent damages
and inconvenience due to accidents. Please read this and use the
product properly.
Do not install or repair the product
randomly as you want.
Do not install the product in a location
where the gap between the door and
doorframe is more than 5mm.
Cautiously manage the passcode so
that other people cannot know it, and
regularly change the number.
Do not operate the product when your
hand is wet, and be careful to not let
water, beverages, and other liquid to
get inside the product.
Do not forcibly press or use a sharp
tool to hit the button.
When you are going out, always
check the ensure that the door was
fully locked.
Properly fit the battery into the product
onto its accurate (+/-) terminals.
When the battery is incorrectly placed
in its direction or charge as displayed
into the battery room, leakage and
breakage may occur, so please be
careful.
When the battery life is ended, replace
all the batteries at once, and avoid
using new and used batteries at the
same time.
When cleaning the product, do not
wipe it with water, benzene, or
alcohol, and instead, use a dry cloth.
Replace the batteries to new ones
within one week of first hearing the
battery replacement notification alarm.
Product Components
Product components may be changed depending on the
installation environment.
Outside
of Main Unit
Doorframe Strike Plate
(Strike)
Key-Tag (2EA)
'AA' Battery (LR6) (4EA)
Spacer
Instruction Manual
Installation Screw
Installation
Paper Diagram
Inside of Main Unit
Fixed Panel
Warning
You must carry or keep at least one
emergency key outside.
In the case of an emergency, please
read and learn the instruction for
manual switchgear.
Names and Features (Outside)
Number cover opened
Number cover
closed
Number cover
Reset hole
Number keypad
Display lamp
Card recognition
button
External power
contact are
Opened
Close
Card
recognition
area
Names and Features (Intside)
Registration Button
OPEN Button
Manual Switchgear
Deadbolt
Door Opening Sensor
Automatic/Manual Lock
Conversion Switch
Gently press the battery cover of the main unit on the
inside and pull the cover in the direction shown in the
arrow.
Opening the cover of the main unit on the inside
Opening the door from the outside
(passcode)
Initialization
(master information, passcode, card, key tag)
Passcode Registration
1. Press the [Number Input] button.
1. Press the [Register] button.
2. Register the new passcode.
1. Press the [Register] button.
1. Press the
[Register] button.
2. Enter the master
information
3. Enter the master
passcode
Register the first master passcode
2. Enter master passcode.
Only applicable in using master information
1. Press the
[Register] button.
2. Contact card and
key tag.
3. End card key
registration
Raise the [number cover]
- With the number cover open,
press the [*] button
At the card recognition area,
contact the card and key tag
Lower the [number cover]
Open the battery cover and
shortly press [register] button.
Open the battery
cover and shortly
press [register]
button.
To end registration,
press the [register]
button of the main
unit on the inside.
Contact the card or key
tag that needs to be
registered.
Enter the new passcode (4~12
digits) and press the [*] button.
Open the battery cover and
press the [register] button for
about 5 seconds.
Open the battery
cover and press the
[register] button
shortly.
1. Press the [Register] button.
2. Enter the master information.
Change the master passcode (if already registered)
Open the battery cover and
press the [register] button
shortly.
When the light comes onto the
number keypad, enter '88' and
then press [*] button.
3. Enter the master passcode
4. Enter the master passcode
that is to be changed.
Enter the master passcode that
you would like to register, and
press [*] button
Enter the master passcode
that is to be changed, and
then press [*] button.
When the light comes
onto the number
keypad, enter '88' and
then press [*] button.
Enter the master
passcode that you
would like to register,
and press [*] button.
When the light comes onto the
number keypad, enter the passcode
and then press the [*] button
2. Enter the passcode.
3. Lower the [number cover]
Success :↑Ding Dong Deng Dong Melody
Fail : Ding Dong Ding Dong Melody
When all of the lights in the number
keypad show up, enter the passcode
and press [*] button.
Reference
With the number cover opened, card or key tag is not recognized.
For the card that is not automatically recognized, press the
[card recognition] button and then try to be authenticated.
Reference
Opening the door from the outside
(card, key tag)
Success :↑Ding Dong Deng Dong
Fail : Ding Dong Ding Dong
Things to know before using this product
※ All registration and setting operate only when the door is open.
※ In addition to regular passcode, card, and key tag, master
information )passcode, card, and key tag) may be registered
additionally for use. Master information is not erased in the case of
regular passcode, card, and key tag registration. When the product
is first purchased, there is no registered master information
Tip : If the master information is registered, pressing register
button shortly will give "ding dong dong ding" sound instead of
"ding dong" sound.
Passcode can be registered in 4~12 digits, and only one
can be registered to use
All registered information, including master information, are
deleted. When registered information is initialized, the passcode
is set to be '1234’.
Registration and changes to master passcode
Master passcode can be registered in 4~12 digits, and only one
master passcode can be registered to use.
Card and Key Tag Registration
When card or key tag is registered, previously registered card
and key tag information are all deleted, so try to register all
cards and key tags at once. Total of 20 card keys and key
tags can be registered (ISO 14443 Type A support)
Caution
Please be careful to manage the passcode so that other people will
not know. Using the same passcode for a long period of time may
lead to its exposure, so regularly change the passcode for use.
Registered passcode cannot be deleted, so register a new passcode
to use.
Caution
To register various cards and key tags continuously, register the card
or key tag, and contact another card or key tag within 10 seconds. If
another card or key tag is not registered within 10 seconds, the
registration automatically ends.
To check if the card or key tag is normally registered, check the card
and key tag, and then close the door.
"Samsung SNS Doorlock" abides to the "ISO 14443 Type A standards,
and the cards, key tags, and NFC-use smartphones that completed
certification from "Samsung SNS Doorlock" are able to be registered on
the doorlock for use.
Reference
Registered master passcode cannot be deleted, so it needs to be
changed to a new master passcode or used with initialization method to
delete all the registered information (master information, passcode,card,
and key tag).
