ENGLISH
A
C
D
B
N (2x)
K
J
Ensure tight cable
connection.
Lay excess cable flat inside the
bottom of the interior housing.
Install interior assembly
align
A
B
C
G
M
R
K
P (3x)
If needed, re-key the
lock to work with your
existing key. See the
supplied SmartKey
Re-key instructions for
more information.
ball tip
Keep “R” in a safe place, as you will
need it to access the back panel for
additional programming.
Install the battery cover and re-key the lock
Programming
instructions are
located on the
reverse side of
this document.
Program the lock
B2 / B3
(2x)
B1 (2x)
B
Longer screws install
closest to door jamb.
Install strike
A
A2
Determine required latch and extend latch bolt
For doors with chiseled edge
For doors without chiseled edge
Use and programming
instructions are located on the
reverse side of this document.
A
A2
B
C
D
E
F
H
J
L
M
K
N
Q
R
P
G
B1
B2
B3
Parts in the Box
Latches and Strikes
Exterior Assembly
Interior Assembly
9
Required Tools
Additional Tools (depending on application)
1"
25 mm
2-1/8"
54 mm
1-1/2"
38 mm
1-3/8" — 1-3/4"
35 mm — 44 mm
Check dimensions
Additional door preparation may be
required for doors with 1-1/2"
(38 mm) holes. Consult the drilling
instructions at www.weiserlock.com.
2-3/8" (60 mm)
or
2-3/4" (70 mm)
or
180°
A
B
A / A2
Hold the latch in front of the
door hole, with the latch face
flush against the door edge.
If the latch holes are
centered in the door hole, no
adjustment is required.
Proceed to step 4.
If the latch holes are NOT
centered, adjust latch. See
“Latch Adjustment.”
Latch Adjustment (only if needed)
Adjust the backset of latch (if needed)
A
A2
C (2x)
A
B
C
D
Install latch
For doors with chiseled edge
For doors without chiseled edge
wood
block
2-1/8"
54 mm
1-1/2"
38 mm
F
F
E
F
E
Prepare exterior keypad
For doors with 2-1/8" (54 mm) holes
For doors with 1-1/2" (38 mm) holes
Make sure “F” is
installed on “E”
Remove and
discard “F”
A
B
C
D
Q (2x)
E
J
H
Q
Keep parallel to
edge of door
Tighten
screws
evenly
Insert key and test latch. If
latch does not extend or
retract smoothly, adjust
screws (Q).
Remove key when finished
and make sure the latch
bolt is fully extended.
Install keypad and mounting plate
Cable goes
underneath
latch
Route cable
through center
hole, then push
cable into
bottom hole.
A
B
C
D
E
M
M
K
K
L
K
AA
L
4x
Disassemble interior assembly and load battery pack
Make sure
turnpiece is in the
vertical position.
Make sure
turnpiece shaft is
rotated as shown.
Ensure correct polarity. For best
results, use new non-rechargeable
Alkaline batteries only.
Do not install
battery pack yet!
1-3/4
" (44 mm)
1-3/8
" (35 mm)
2-3/8" (60 mm)
2-3/4" (70 mm)
Edge
Backset
Face
Centerline
If your door requires drilling, cut out the template and place it on the exterior side of the door.
Complete door drilling instructions are available on the SmartCode deadbolt page of www.weiserlock.com.
Template
Fold
Installation Guide
A
B
L
L
Press and hold
the
Lock button while
installing battery
pack (L).
Hold button until the
latch bolt starts
moving on its own.
This step will teach your lock the orientation of your door
and is crucial to lock operation.
HOLD
latch bolt
Did the latch bolt retract
and extend on its own
when the battery pack
was installed?
Door handing process
was successful!
Proceed to Step 11
after latch bolt stops
moving.
Remove battery pack,
wait 15 seconds, then
attempt the process
again.
YES
NO
Perform door handing process
10
11
12
13
A
B
C
12"
305 mm
L
L
Perform the Inclusion process (Z-Wave locks only)
Hold the interior assembly a maximum of 12" (305 mm) from your Z-Wave
controller, and initiate the Inclusion process at the controller. Refer to your
Z-Wave control system instructions for more information.
Press button “A” on the lock one time to include it in your system. The
controller and lock must remain stationary for a total of 60 seconds during
the Inclusion process.
If Inclusion is unsuccessful, initiate the Exclusion process at the controller,
then press button “A” on the lock one time. Once the lock is fully excluded
from the system, repeat the Inclusion process.
“Inclusion” refers to the process in which the lock is added to a Z-Wave or ZigBee controller.
ZigBee locks: Perform the Inclusion process after installation is complete.
See “Z-Wave and ZigBee Systems” on the reverse side of this document.
Button
“A”
Z-Wave
Controller
3
4
5
6
7
8
1
2
61041 / 02
GED1800
