Regency B36XT Bellavista Owners & Installation Manual Download

Page: 1 / 68

WARNING:
If the information in these instructions are not followed exactly,
a fi re or explosion may result causing property damage,
personal injury or loss of life.

FOR YOUR SAFETY
Do not store or use gasoline or other fl ammable vapors and
liquids in the vicinity of this or any other appliance.

Installation and service must be performed by a qualifi ed
installer, service agency or the gas supplier.

FOR YOUR SAFETY
What to do if you smell gas:
Do not try to light any appliance
Do not touch any electrical switch:

do not use any phone in your
building.

Immediately call your gas supplier

from a neighbour's phone. Follow
the gas supplier's instructions.

If you cannot reach your gas

supplier, call the fi re department.

FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4

918-769c

Regency Bellavista

™

B36XT

Gas Fireplace
Gas Fireplace

05/05/14

Owners &

Installation Manual

www.regency-fi re.com

Tested by:

Installer: Please complete the details on the back cover

and leave this manual with the homeowner.

Homeowner: Please keep these instructions for future reference.

MODEL: B36XT

Medium DV Gas Fireplace

Bellavista B36XT Video

Summary of Contents for B36XT Bellavista





































































Search results

Summary of Contents for B36XT Bellavista

Reviews:

Related manuals for B36XT Bellavista

Brands by name

Popular brands

Regency B36XT Bellavista, Owners & Installation Manual

Search results

Summary of Contents for B36XT Bellavista

Reviews:

Related manuals for B36XT Bellavista

Brands by name

Popular brands