background image

Heat & Glo  •  6000PLUS  •  2063-900  Rev. E  •  11/05

1

• Do not store or use gasoline or other flamma-

ble vapors and liquids in the vicinity of this or

any other appliance.

• What to do if you smell gas

- Do not try to light any appliance
- Do not touch any electrical switch. Do not

use any phone in your building.

- Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

- If you cannot reach your gas supplier, call

the fire department.

• Installation and service must be performed by

a qualified installer, service agency, or the gas

supplier.

WARNING:  If the information in these

instructions is not followed exactly, a fire

or explosion may result causing proper-

ty damage, personal injury, or death.

This appliance has been supplied with an integral barrier

to prevent direct contact with the fixed glass panel. Do

NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the

barrier is not present or help is needed to properly install one.

HOT! DO NOT TOUCH

.

SEVERE BURNS MAY RESULT.

CLOTHING IGNITION MAY RESULT.

WARNING

• Keep children away.

• CAREFULLY SUPERVISE children in same room as

appliance.

• Alert children and adults to hazards of high

temperatures.

• Do NOT operate with protective barriers open or

removed.

• Keep clothing, furniture, draperies and other

combustibles  away.

Glass  and  other  surfaces  are  hot  during

operation and cool down.

This appliance may be installed as an OEM installation in

manufactured home (USA only) or mobile home and must

be installed in accordance with the manufacturer’s instruc-

tions and the manufactured home construction and safety

standard,

Title 24 CFR, Part 3280 

or

Standard for Installa-

tion in Mobile Homes, CAN/CSA Z240MH.
This appliance is only for use with the type(s) of gas indi-

cated on the rating plate.

Installation and service of this appliance should be

performed  by  qualified  personnel.  Hearth  &  Home

Technologies suggests NFI certified or factory-trained
professionals, or technicians supervised

by an NFI certified professional.

In the Commonwealth of Massachusetts:
•  installation must be performed by a licensed plumber

or gas fitter;

• a CO detector shall be installed in the room where the

appliance is installed.

DO NOT DISCARD THIS MANUAL

CAUTION

Important  operating  and

maintenance  instruc-

tions  included.

Read,  understand  and  follow

these  instructions  for  safe

installation  and  operation.

Leave this manual with

party  responsible  for

use  and  operation.

Model:

6000PLUS

Owner’s  Manual

Installation and Operation

THE 6000PLUS IS DESIGNED TO BE

USED WITH THE HRV200PLUS ONLY!

THE 6000PLUS WILL NOT VENT CORRECTLY UN-

LESS IT’S CONNECTED TO THE HRV200PLUS.

REFER TO THE HRV200 PLUS INSTALLATION

MANUAL FOR ADDITIONAL INSTALLATION

AND VENTING INSTRUCTIONS.

WARNING

DO N

O

DO N

O

DO N

O

DO N

O

DO N

OTTTTT

DISC

ARD

DISC

ARD

DISC

ARD

DISC

ARD

DISC

ARD

Summary of Contents for 6000PLUS




















Reviews: