Potterton Suprima 100 Installation & Service Instructions Manual Download

Page: 1 / 38

Installation & Service Instructions

Suprima 100

Wall Mounted Fan Assisted

Balanced Flue Gas Boilers

THE GAS SAFETY (INSTALLATION AND USE) REGULATIONS 1994 (as amended).

‘‘ In your own interest, and that of safety, it is law that all gas appliances are installed by competent persons,

in accordance with the above regulations. Failure to install appliances correctly could lead to prosecution.’’

Installation must be in accordance with the Installation & Service Instructions and the rules in force.

LEAVE THESE INSTRUCTIONS WITH THE USER FOR USE ON FUTURE CALLS

For Use With Natural Gas
(G20) Only At 20mbar
For Use in GB & IE

IMPORTANT

PLEASE READ THIS BOOK
BEFORE INSTALLING,
OPERATING OR SERVICING
THIS BOILER.

Summary of Contents for Suprima 100







































Search results

Summary of Contents for Suprima 100

Reviews:

Related manuals for Suprima 100

Brands by name

Popular brands

Potterton Suprima 100, Installation & Service Instructions Manual

Search results

Summary of Contents for Suprima 100

Reviews:

Related manuals for Suprima 100

Brands by name

Popular brands