Installation Guide Lighting Fixture
Installation Guide
Lighting Fixture
Input voltage
Input current
Input wattage
29.0W / 30.3W
95 mm × 95 mm
3 47/64” × 3 47/64”
Ceiling cut out
MMP-080F/CWF.CMF/20B/Z1/2
MUSEUM DOWNLIGHT FOUNDATION
120V / 277V
0.26A / 0.13A
Ceiling
Weight
thickness
The fixture is for indoor use only in general conditions.This fixture can only be installed on a horizontal ceiling.
Can not be used following conditions (Causes of falling, electrocution and fire)
●Ambient temperature under 0℃ and over 35℃
●High humidity
●Outside
●On the floor
●Vibrated or shocked areas
●Areas get direct sunlight
●Inclined, uneven surface
●Ceiling which canʼt hold the fixture weight
●On the wall
●Places affected by wind or air-conditioner machine
●Near fire
●Dusty areas, corrosive gas outbreaks areas
Before
installation
For electric
wiring
At lighting
fixture
installation
Warning
Warning
Warning
Warning : Failure to install the fixture properly could result in personal injury.
Failure to install the fixture properly could result in property damage.
: Prohibited
Read and understand these instructions before installing fixture.
Retain these instructions for maintainance reference.
This fixture is intended for installtion in accordance with the National Electrical Code and local regulations. To assure full compliance with
local codes and regulations, check with your local electrical inspector before installation. To prevent electrical shock, turn off electricity at
fuse box before proceeding.
: Strict observance
Caution :
Caution
Caution
To install the fixture safely《 Read carefully and follow all the instructions in the guide 》
Please follow the fixturesʼ indication or specification for the distance of irradiated area.
(Causes of change in shape, change in color of irradiated objects)
Please contact if you are not able to judge whether installation
environment is suitable to the places or not.
Only qualified person may work on electric wiring and equipment. (Cause of accidents)
Be sure power supply voltage is within ±6% mentioned in rating plate or the guide. (Causes of short life of lamps・electrification・fire)
Be sure all the wires and codes are not damaged. (Causes of falling・damage)
Please follow the fixturesʼ instruction or this guide to install the fixture and lamp. (Causes of falling・electrification・fire)
Switch off the power when installing the lamp. (Causes of electrification)
Do not touch the fixture when switch is on or just turn off the switch because of high temperature.
Do not put or cover the fixture by any cloths, papers, or insulators.(Causes of not lighting・fire)
Do not place any metallic or flammable objects. (Cause of electrification・fire・broken fixture)
Make sure to install all the parts of fixtures besides installation and mounting parts will not touch with any
objects both inside and outside of ceiling such as lighting track, etc. (Causes of falling・electrification・fire)
Do not dismount or remodel fixtures. (Cause of electrification・fire・falling・broken fixtures)
Do not operate with wet hands.
If you smell smoke, see smoke, or find anything unusual, please turn the switch off and ask construction
companies to repair. (Cause of electrification・fire)
Make sure the construction will not affect any fire prevention systems such as sprinkler by heat from the fixture.
(Causes for improper operation)
Use alternating current. Please follow rating plate of fixtures for power supply frequency.
(Cause of electrification・fire) (50Hz ・60 Hz common use for ballasts and incandescent lamp fixtures)
LED DRIVER (BUILT-IN)
OT40W/PRG1400C/UNV/DIM
(OSRAM)
Please use the dimmer
adapted to the led driver
5
39
/6
4"
4 9/64"
8 5/16"
1 1
1/6
4"
10 3/64"
4
13
/3
2"
2 13/16" 71.5mm
255mm
111
.9m
m
142
.5m
m
211mm
29.
6m
m
23
/6
4"
-6
3/
64
"
9-2
5m
m
3m
m
1/
8"
105mm
2.183 lbs
990 g
9〜25mm
23/64”
~63/64”
