CONGRATULATIONS!
You’ve purchased the finest in natural lighting
technology with your new OttLite
®
product.
PRODUCT REGISTRATION FORM
Please complete the enclosed Product Registration
Form and return it today by mail, or register online
by going to: www.ottlite.com/warranty
NOTE: THIS UNIT IS FULLY ASSEMBLED
1.
Remove lamp from packing.
2.
Grasp clamp (A) and neck to securely clamp
lamp to easel or table.
3.
Connect adaptor (B) to lamp.
4.
Verify the lamp is secure before using.
5.
Plug adaptor (C) into a standard 120V household
outlet.
6.
Turn the lamp ON/OFF using switch (D) located
on cord.
7.
To position the LED light assembly (E) simply
bend the flex-neck as needed to point the light,
ensuring clamp does not come loose.
NOTE:
To avoid damaging the lamp,
DO NOT
force flex-neck into a sharp bend.
SAFETY WARNING:
TO REDUCE THE RISK OF FIRE,
ELECTRIC SHOCK, OR INJURY TO PERSONS
1.
Turn lamp off and
WAIT UNTIL LAMP HEAD
COOLS before handling.
2.
The LED panel might get hot after several hours
of continuous use,
DO NOT place your hands
directly on LED light panel.
3.
Never use with an extension cord unless the
plug can be fully inserted into the receptacles
in the extension cord.
4.
Do not alter the plug.
5.
The lamp head included with this unit cannot be
replaced by the consumer.
6.
INDOOR USE ONLY.
NOTE:
The important safety instructions
appearing in this instruction sheet are not meant
to cover all possible conditions and situations that
may occur. It must be understood that common
sense, caution, and care must be used with any
electrical product.
CAUTION!
IF THE EXTERNAL FLEXIBLE CABLE OR CORD
OF THIS LUMINAIRE IS DAMAGED, IT SHALL BE EXCLUSIVELY
REPLACED BY THE MANUFACTURER OR ITS SERVICE AGENT OR
A SIMILAR QUALIFIED PERSON IN ORDER TO AVOID A HAZARD.
INDOOR USE ONLY.
CAUTION!
THE LIGHT SOURCE OF THIS LUMINAIRE IS NOT
REPLACEABLE; WHEN THE LIGHT SOURCE REACHES ITS END OF
LIFE THE WHOLE LUMINAIRE SHALL BE REPLACED.
FCC PART 15
Note: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part
15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that the
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit
different from that of the receiver.
• Consult the dealer or an experienced radio/TV technician
for help.
Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate
the equipment.
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation
CAUTION!
Any change or modification to product not
expressly recognized by OttLite Technologies voids
OttLite’s responsibility for proper function of product.
CAN ICES-005 (B)/NMB-005 (B)
POWER ADAPTER SPECIFICATIONS:
Input: AC 100-240V, 50/60 Hz, 0.3A
Output: 12V DC, 0.5A with a Male DC Plug
INS-21-0628
REV022521
A
B
C
D
E
ENGLISH
Clip-On LED Easel Lamp
Clip-On LED Easel Lamp
CSJ37G5C CSJ37PNC
MA02
