Mighty Mule MM560 Installation Manual Download

Page: 1 / 44

Printed in China for GTO Access Systems, LLC.

Copyright

2016 GTO Access Systems, LLC

Document Number: R56008 REV A (12.15.16)

GTO Sales: 800-543-4283 • Fax 850-575-8912

GTO Technical Service 800-543-1236

For 24 hour/day, 7 day/week Technical Service visit http://support.gtoinc.com

For more information on Mighty Mule’s full line of Automatic Gate Operators and Access Controls visit

www.mightymule.com

MM560

ACCESS SYSTEMS, LLC

Mighty Mule® is the retail brand of GTO Access Systems, LLC

3121 Hartsfield Road • Tallahassee, FL 32303

This product meets the requirements of UL325 6th Edition, 2016, the standard for gate

operator safety.

Installation Manual

Horizontal Support

Gate Swings Evenly and Freely

Hung Firmly and Plumb

Receiver

Post Bracket

Control Box with Battery

Fence Post Set in Concrete

Run 1000' (max.) of low

voltage wire to control

box from transformer

(wire not included).

Power Cable

Closed Position Stop Plate

PVC conduit (not included)

to protect wire from lawn

mowers and weed eaters.

Gate Bracket

Warning Sign

Single Gate Opener

120 Volt indoor

Transformer

(surge protector

not supplied)

Example of finished installation

(installations vary slightly on different types of gates)

Summary of Contents for MM560













































Search results

Summary of Contents for MM560

Reviews:

Related manuals for MM560

Brands by name

Popular brands

Mighty Mule MM560, Installation Manual

Search results

Summary of Contents for MM560

Reviews:

Related manuals for MM560

Brands by name

Popular brands