background image

 

Instruction Manual 

HF Mobile 

Ham-tenna

TM

 Whips

 

 

Power Rated at 250 Watts P.E.P. 

 
These HF antennas are designed to operate over the phone 
portion of HF bands with a typical VSWR of 2:1. 
 
MFJ offers the following HF Mobile 

Ham-tenna

TM

 whips: 

MFJ Model No. 

Band 

MFJ Model No. 

Band 

MFJ-1675T 75 

Meter 

MFJ-1615T 15 

Meter 

MFJ-1640T 40 

Meter 

MFJ-1612T 12 

Meter 

MFJ-1630T 30 

Meter 

MFJ-1610T 10 

Meter 

MFJ-1620T 20 

Meter 

MFJ-1606T 6 

Meter 

MFJ-1617T 17 

Meter 

MFJ-1602T 2 

Meter 

 

Tuning Instructions: 

Insert the whip into the lower section ferrule about four 
inches and tighten the set screw.  Screw the ferrule/whip 
assembly into the lower fiberglass section.  Install a VSWR 
meter at the transceiver and apply 10 or 25 watts of power.  
Adjust the VSWR meter and output frequency for lowest 
VSWR reading, indicating resonance.  If resonant frequency 
is higher than desired, loosen the set screw and extend the 
top whip until the desired resonant frequency is found.  If 
resonant frequency is too low, loosen the set screw and 
adjust the whip further into the lower section.  For best 
results, adjustments should be made in small increments. 
 

Caution: 

If required, cut off the bottom of the whip to ensure 

it does not extend down into the coil.  Failure to observe this 
precaution will cause extreme heat damage and void the 
warranty. 
 

VSWR:

 At resonance, the VSWR should be 1.5:1 or less 

when properly matched.  When tuning is complete, tighten 
the set screws securely. 
 

NOTE:

 Bandwidth and VSWR will vary due to mounting 

location.  Roof mounts, trunk groove mounts, and trunk lip 
mounts are recommended.  The poorest mount is a bumper 
mount.  If your installation has a VSWR over 1.5:1 at 
resonance or you need to operate over a greater bandwidth, 
a tuner may be required. 
 

STORAGE:

 To store your HF 

Ham-tenna

TM

, unscrew the 

ferrule/whip assembly from the lower fiberglass section.  

Note:

 If only the whip is removed, repeat tuning procedure 

before using again. 
 

MFJ Enterprises, Inc. 

…The World Leader in Ham Radio Accessories 

300 Industrial Park Road, Starkville, MS 39759 USA 

Phone: (662) 323-5869 Fax: (662) 323-6551 

http://www.mfjenterprises.com

 

Made in the U.S.A. 

 

Instruction Manual 

HF Mobile 

Ham-tenna

TM

 Whips

 

 

Power Rated at 250 Watts P.E.P. 

 
These HF antennas are designed to operate over the phone 
portion of HF bands with a typical VSWR of 2:1. 
 
MFJ offers the following HF Mobile 

Ham-tenna

TM

 whips: 

MFJ Model No. 

Band 

MFJ Model No. 

Band 

MFJ-1675T 75 

Meter 

MFJ-1615T 15 

Meter 

MFJ-1640T 40 

Meter 

MFJ-1612T 12 

Meter 

MFJ-1630T 30 

Meter 

MFJ-1610T 10 

Meter 

MFJ-1620T 20 

Meter 

MFJ-1606T 6 

Meter 

MFJ-1617T 17 

Meter 

MFJ-1602T 2 

Meter 

 

Tuning Instructions: 

Insert the whip into the lower section ferrule about four 
inches and tighten the set screw.  Screw the ferrule/whip 
assembly into the lower fiberglass section.  Install a VSWR 
meter at the transceiver and apply 10 or 25 watts of power.  
Adjust the VSWR meter and output frequency for lowest 
VSWR reading, indicating resonance.  If resonant frequency 
is higher than desired, loosen the set screw and extend the 
top whip until the desired resonant frequency is found.  If 
resonant frequency is too low, loosen the set screw and 
adjust the whip further into the lower section.  For best 
results, adjustments should be made in small increments. 
 

Caution: 

If required, cut off the bottom of the whip to ensure 

it does not extend down into the coil.  Failure to observe this 
precaution will cause extreme heat damage and void the 
warranty. 
 

VSWR:

 At resonance, the VSWR should be 1.5:1 or less 

when properly matched.  When tuning is complete, tighten 
the set screws securely. 
 

NOTE:

 Bandwidth and VSWR will vary due to mounting 

location.  Roof mounts, trunk groove mounts, and trunk lip 
mounts are recommended.  The poorest mount is a bumper 
mount.  If your installation has a VSWR over 1.5:1 at 
resonance or you need to operate over a greater bandwidth, 
a tuner may be required. 
 

STORAGE:

 To store your HF 

Ham-tenna

TM

, unscrew the 

ferrule/whip assembly from the lower fiberglass section.  

Note:

 If only the whip is removed, repeat tuning procedure 

before using again. 
 

MFJ Enterprises, Inc. 

…The World Leader in Ham Radio Accessories 

300 Industrial Park Road, Starkville, MS 39759 USA 

Phone: (662) 323-5869 Fax: (662) 323-6551 

http://www.mfjenterprises.com

 

Made in the U.S.A.

Reviews: