background image

 

SPECIFICATIONS 

MODEL NUMBER ................................................ KT36XA   
FREQ. RANGE..................................................... 14.0 - 14.35 MHz 
 

21.0 - 21.45 MHz 

 

28.0 - 29.0   MHz 

GAIN (Free Space) .............................................. SEE CHARTS 
FRONT TO BACK ................................................ SEE  CHARTS 
FEED IMPEDANCE / CONNECTOR ................... 50

 / SO-239  

VSWR ................................................................... <1.5:1   
POWER HANDLING ............................................ 3  kW 
BOOM LENGTH / DIAMETER ............................. 32’ / 3” 
ELEMENT LENGTH ............................................. 25’ 
TURNING RADIUS .............................................. 21.5’ 
MAST SIZE .......................................................... 2” Nominal 
WIND AREA ......................................................... 9.75 SQ. FT. 
WIND SURVIVAL ................................................. 100 MPH 
WEIGHT / SHIPPING WEIGHT ........................... 80 lb. / 85 lb. 2 boxes

 

FEATURES 

The M

2

 KT36XA is the result of many hours spent on perfecting the original KLM KT-34XA through computer 

optimization confirmed by range and actual on-air tests.  Five elements are active on 20 and 15 meters and all 
six are working on 10 meters!  This is the hottest performing tribander on the market!

 

A dual driven element 

(log cell) creates a rig pleasing, flat match, and broad gain & front to back curves across 10, 15, and 20m.  A 3 
kW 4:1 balun efficiently matches the antenna to 50

.  All hardware has been upgraded to our machined 

shorting bars and rugged center element mounts. This is the strongest tribander on the market! We probably 
could have called it the “KB36XA” cuz it does!  (“KB” = Kicks Butt).

 

10m

 

 

 

 

f, MHz

 

G, dBi

 

G, dbd 

F/B

 

28.0

 

9.8

 

7.7 25

 

28.2

 

10.1

 

8.0 28

 

28.4

 

10.4

 

8.3 29

 

28.6

 

10.5

 

8.4 28

 

28.9

 

10.5

 

8.4 26

 

15m

 

 

 

 

f, MHz

 

G, dBi

 

G, dbd 

F/B 

 

21.0

 

9.2

 

7.1 19

 

21.1

 

9.3

 

7.2 22

 

21.2

 

9.4

 

7.3 24

 

21.3

 

9.5

 

7.4 24

 

21.4

 

9.6

 

7.5 23

 

20m

 

 

 

 

f, MHz

 

G, dBi

 

G,dbd 

F/B

 

14.0

 

9.1

 

7.0 17

 

14.1

 

9.2

 

7.1 26

 

14.2

 

9.3

 

7.2 21

 

14.3

 

9.4

 

7.3 23

 

M2 Antenna Systems, Inc. 4402 N. Selland Ave. Fresno, CA 93722 

Tel: (559) 432-8873 Fax: (559) 432-3059 Web: www.m2inc.com 

©2015 M2 Antenna Systems Incorporated 

2/13/15 

Rev.03 

M2 Antenna Systems, Inc. 

Model No: KT36XA 

Summary of Contents for KT36XA





















Reviews: