Incra Twin Linear Owner'S Manual Download

Page: 1 / 20

OWNER’S MANUAL

Please read this Ownerʼs Manual before

use and keep it at hand for reference.

NOTE

If you are setting up the TWIN at your

table saw, follow the mounting instructions

included with the TSII Base Mount Kit

-1

Hi-Rise fence cap

Infeed carriage

(black)

Carriage clamp

Outfeed fence

Red

micro adjust

knob

Dust

collection

port

Rear black thumbscrew (Tighten only

during outfeed fence offset adjustments)

Fence cap braces

Stainless steel

primary scale

Black infeed fence

adjustment knob

Infeed fence

Forward black thumbscrew (Loosen only during fence

offset adjustments

Outfeed carriage

(gold)

Lexan

“floating” scale

Hairline cursor

Fence mounting

bracket

Base

Please take just a few minutes of your time to read

your new INCRA TWIN LINEAR ownerʼs manual.

Youʼll find it full of interesting and useful information

about safety, setting up, and putting to use the many

wonderful features of the TWIN. And itʼs all written

by someone who continues to use every INCRA

product from the very first INCRA Jig all the way up

to our best offering ever — the INCRA TWIN LINEAR!

In eight years of using one INCRA Jig or another

virtually every weekend (and some week nights) Iʼve

come to know these tools inside out. In writing this

manual I want to share this experience with you. Iʼve

attempted to make everything as clear as possible,

but if you are in doubt, weʼll be here to help. See

you in the shop!

—

Perry

Summary of Contents for Twin Linear





















Search results

Summary of Contents for Twin Linear

Reviews:

Related manuals for Twin Linear

Brands by name

Popular brands

Incra Twin Linear, Owner'S Manual

Search results

Summary of Contents for Twin Linear

Reviews:

Related manuals for Twin Linear

Brands by name

Popular brands