background image

Printed in U.S.A.

441 01 2314 06   July 2010

INSTALLATION INSTRUCTIONS

80% Single Stage, Downflow, 

Category I, Gas Furnace

C8DNL, H8DNL, T8DNL

These instructions must be read and understood completely before attempting installation.

Safety Labeling and Signal Words

DANGER, WARNING, CAUTION, and NOTE

The signal words 

DANGER, WARNING

,

CAUTION

,

 

and

 NOTE 

are used to identify levels of

hazard seriousness. The signal word

 DANGER 

is

only used on product labels to signify an immediate

hazard. The signal words 

WARNING

CAUTION

,

and 

NOTE

 will be used on product labels and

throughout this manual and other manual that may

apply to the product.

DANGER

 

 Immediate hazards which will result in

severe personal injury or death.

WARNING

 

 Hazards or unsafe practices which

could result in severe personal injury or death.

CAUTION 

 Hazards or unsafe practices which

may result in minor personal injury or product or

property damage.

NOTE 

 Used to highlight suggestions which will

result in enhanced installation, reliability, or

operation.

!

WARNING

Signal Words in Manuals

The signal word 

CAUTION

 is used throughout

this manual in the following manner:

!

CAUTION

Signal Words on Product Labeling

Signal words are used in combination with

colors and/or pictures or product labels.

The signal word 

WARNING

 is used throughout

this manual in the following manner:

Safety

alert symbol

When you see this symbol on the unit and in

instructions or manuals, be alert to the

potential for personal injury.

TABLE OF CONTENTS

SAFETY CONSIDERATIONS

2

. . . . . . . . . . . . . . . . . . .

Safe Installation Requirements

3

. . . . . . . . . . . . . . . . . .

INSTALLATION

4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Combustion & Ventilation Air

6

. . . . . . . . . . . . . . . . . . . .

Gas Vent Installation

9

. . . . . . . . . . . . . . . . . . . . . . . . . . .

Venting (Horizonta)

10

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Venting (Chimney Adapter)

12

. . . . . . . . . . . . . . . . . . . . .

Gas Supply and Piping

15

. . . . . . . . . . . . . . . . . . . . . . . . .

Electrical Wiring

17

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Ductwork and Filter

18

. . . . . . . . . . . . . . . . . . . . . . . . . . . .

Checks and Adjustments

23

. . . . . . . . . . . . . . . . . . . . . . .

Furnace Maintenance

27

. . . . . . . . . . . . . . . . . . . . . . . . . .

Sequence of Operation & Diagnostics (*8DNL)

28

. . . .

Wiring Diagram (*8DNL)

32

. . . . . . . . . . . . . . . . . . . . . . .

International Comfort Products, LLC

Lewisburg, TN 37091 U.S.A.

!

WARNING

PERSONAL INJURY, AND/OR PROPERTY

DAMAGE HAZARD

Failure to carefully read and follow this warning could

result in equipment malfunction, property damage,

personal injury and/or death.

Installation or repairs made by unqualified persons

could result in equipment malfunction, property

damage, personal injury and/or death.

The information contained in this manual is intended for

use by a qualified service technician familiar with safety

procedures and equipped with proper tools and test

instruments.

Installation must conform with local building codes and

with the Natural Fuel Gas Code (NFCG) NFPA 54/ANSI

Z223.1, and National standards of Canada

CAN/CSA

B149.1 and .2 Natural Gas and Propane

Installation Codes.

INSTALLER:

 Affix these instructions on or adjacent to the

furnace.

CONSUMER:

 Retain these instructions for future refer-

ence.

Portions of the text and tables are reprinted from NFPA 54 /ANSI Z223.1

2009

©

, with permission of National Fire Protection Association, Quincy, MA 02269 and American Gas Association, Washington,

DC 20001.  This reprinted material is not the complete and official position of the NFPA or ANSI, on the referenced subject, which is represented only  by the standard in its entirety.

Summary of Contents for C8DNL




































Reviews: