Bolid Security Systems RIP-12 02, Instruction Manual

Page: 1 / 2

RIP-12 SHUTTING OFF
1) Shut off the mains power supply 220 V.
2) Detach the battery.
3) Remove the fuse F1.
4) Disconnect the load circuit.
MAINTENANCE
The maintenance of RIP-12 is to be carried out annually. The maintaining operations include:
1)
RIP-12 visual inspection to discover mechanical injures and to clean any dirt or dust if presented.
2) Measuring the power output parameters and checking them to be in conformance with items of
SPECIFICATION.
3) LED and sound indication testing to meet the requirements of Table above.
4) Proper RIP-12 firmly attaching, and contact tightening, and wire integrity inspection.
WARRANTY
Manufacturer warrants RIP-12 Uninterrupted Power Supply to be free from defects and to operate in
conformance with specification under normal transportation, mounting and maintenance for 18 months since putting
it into operation, but no more than for 24 month since acceptance date (see below).
In the event of in-warranty failure the failed RIP-12 should be brought back to the manufacturer supplied with
its damage certificate describing the defect and its acceptance certificate to validate the warranty status. Send your
complaints to the manufacturer at the following address:
ZAO NVP BOLID
#4, Pionerskaya street, Korolyov, Moscow Region, Russia, 141070
Tel./fax +7 495 777-40-20, +7 495 516-93-72.
E-mail: info@bolid.ru , Web-site: www.bolid.com
ACCEPTANCE CERTIFICATE
RIP-12 Uninterrupted Power Supply model 02
Product Designation Serial Number
Produced, tested by quality control department in compliance with state standards and specifications, packed by
NVP BOLID Company and qualified as deliverable.
Q.C.
STAMP _____________________ ____________________________
Name Date of Acceptance
UNINTERRUPTED POWER SUPPLY
RIP-12 model 02
INSTRUCTION MANUAL
GENERAL
Uninterrupted Power Supply RIP-12 model 02 (referred to as RIP-12 below) is designed to provide the electric
power to various fire and intruder detectors, as long as control and indication equipment suited for uninterrupted 12
VDC.
RIP-12 is round-the-clock operating device with defined output parameters, sealed backup battery being tested
and charged automatically. PIR-12 provides battery shutting off from load circuit in order to avoid its unacceptable
discharge.
RIP-12 is equipped with light and audible indication of its current status, i.e. normal or no voltage, battery
charge, output short failure or overload, battery missing or shutting down when discharged.
When operated, RIP-12 should be protected against atmospheric fallout and mechanical damage.
SPECIFICATION
AC Input Voltage Range – from 187 to 242 VAC @ 50 Hz
Backup Power Supply – battery «Delta» DTM1207 12 V @ 7 Ahr or analogous
Output Voltage Range
– 13.6
±
0.6 VDC at both AC and charged battery powering;
– 11.0
±
0.5 VDC min provided the battery is discharged
Load Current Rating – 2.0 А
Maximum Load Current – 3.0 А within 10 minutes or 5 А within 2 minutes at both mains
and battery powering, once an hour minimum
Input Current Consumption – 0.3 А maximum for rating load
Ripple (mVp-p)×2 – 20 mV maximum at rating load current
Battery Low Shutdown
– 10.2
±
0.6 VDC
On Battery Run-Time – at least 5 hours for 1 A load current, increasing proportionally to
load reduction
Ingress Protection Rating – IP20
Power-Up Operation Readiness – 6 seconds maximum
Operating Temperature Range
– from –10
°
C to +40
°
C
Overall Dimensions – 255 х 310 х 95 mm
RIP With Battery Weight – 6.5 kg maximum
Typical Lifetime – 8 years, the battery being to be replaced once every 5 year
RIP-12 provides protection against short circuit failure along with automatically recovering of output voltage
after short failure disappearing while powered from mains and backup battery.
RIP-12 is equipped with open collector transistor output functioning as contact closure device. It is opened
when AC line fails and RIP-12 is operating in battery mode, or in case of a short load circuit failure, so it can be
used for remote signaling of RIP electric troubles. The maximum output permissible voltage and commutation current
are 30 V and 100 mA respectively.
DELIVERY SET
Uninterrupted Power Supply RIP-12 model 02 - 1
Instruction Manual - 1
Fuse 0.5 А - 1 pc
Screw-nail - 3 pcs
Dowel - 3 pcs
Plastic Bushing - 2 pcs
Front Cover Lock Key - 2 pcs
Package - 1 pc
ISO 9001