5” & 10” roses may
be installed as shown.
Interior Latchset
Installation Instructions
Passage, Privacy, Full & Half Dummy
1. Fold the template
on the line and
locate on at desired
height (about 40”
from floor). Place
folded edge on low
side of door bevel.
Mark holes on door
for appropriate
backset, rose style
and size.
2. Caution: Recheck
bore hole locations
before drilling. Drill
the 2-1/8” Face Bore
through the door first.
Drill the 1” diameter
Edge Bore through
to the inside of the
2-1/8” Face Bore.
For 5” & 10” rose
styles, mark but do
not drill pilot holes
for #8 surface mount
screws. This will be
done in a later step.
3. Insert the latch
into the edge of
the door. Trace
an outline of the
faceplate onto the
door edge. Mark
screw hole center
locations and drill
1/8” pilot holes.
4. Chisel out the
area marked in step
3 to a depth of 5/32”
or until faceplate
is flush with door
edge. Proceed to
Passage or Privacy
installation.
DOOR PREPARATION: PASSAGE & PRIVACY LATCHSETS ONLY
1. Using the strike
portion of the
marking template,
locate and mark
strike mounting
screws and
centering points for
your door thickness.
2. Align the strike
and trace outline
onto the door frame
using mounting
screw marks for
location.
3. At the screw
marks, drill (2) 1/8”
dia. pilot holes for
the screws. Bore
7/8” dia. X 3/4”
deep hole.
4. Chisel out the
area marked in
step 2 to a depth of
1/16” or until strike
is flush with door
frame.
Install strike using
(2) #8 Flat Head
combination screws.
STRIKE PREPARATION: PASSAGE & PRIVACY LATCHSETS ONLY
1. Locate the posi-
tion for hole in door.
If not used with a
double door, the
hole location should
be approx. 40” from
floor. Drill a 5/8”
hole ¼” deep one
side of the door
DO NOT DRILL
THROUGH DOOR
.
2. Place backplate on door so that the flat
surface is toward the floor. The flat surface
should be parallel to the floor and perpen-
dicular to the door edge. A builder’s square
should be used for best results. Using the
backplate as a template, mark center locations
for (3) screw holes.
Remove backplate and pre-drill (3) holes for
screws ½” deep using a 1/16” drill bit. Install
backplate with (3) flat head screws provided.
4. Orient the
knob or lever so
the set screw is
pointed down
& toward the
hinges of the
door. Slide the
knob or lever
onto the end
of the spindle
until it touches
the adaptor and
secure with set
screw.
HALF DUMMY INSTALLATION
BACKPLATE
ROSE
#8 X 3/4” OVAL
HEAD SCREWS
(*See note.)
FLAT HEAD
SCREWS
RETAINER
SET SCREW
KNOB
BACKSET DIMENSION
(2-3/8” OR 2-3/4”)
TEMPLATE
1” DIA.
EDGE
BORE
2-1/8”
FACE
BORE
7/8”
EDGE BORE
1/8” PILOT HOLES
FOR #8 SCREWS
SPANNER TOOL
KNOB
ROSE
1-1/4”
FLAT HEAD
SCREWS
#8 X 3/4”
COMBINATION
SCREWS
SET SCREW
ALIGNMENT
BUSHING
EMERGENCY KEY
(PRIVACY VERSION)
INSIDE
ADAPTOR
LATCH
OUTSIDE
ADAPTOR
ROSE
#8 X 3/4” OVAL
HEAD SCREWS
(*See note.)
RETAINER
ALLEN
WRENCH
PRIVACY BUTTON
(PRIVACY VERSION)
PRIVACY
BUTTON EXTENSION
(PRIVACY VERSION)
FACE
PLATE
*Note: #8 Oval Head Screws are not required on 3” rose styles.
*Note: #8 Oval Head Screws are not required on 3” rose styles.
THREADED STUD
(Privacy Version)
PK.2716
3. Attach the roses
by screwing the
threaded retainer
onto the adaptors.
Orient the rose as
desired and securely
tighten by using the
spanner tool.
For 5” & 10” roses,
ensure rose is paral-
lel with door edge
and drill 3/32” x 1/2“
deep pilot holes at
marked locations.
Install #8 oval head
screws into door.
STRIKE
PLATE
NYLON WASHER
DOOR EDGE
MARK LOCATION
OF 3 SCREW HOLES
DOOR EDGE
a
