background image

RADIUS WEATHER STRIP

RADIUS

  FLAT

AVAILABLE FACEPLATES

3b

FOR APPLICATIONSTHAT REQUIRE

RETRACTION OF THE DEADBOLT 

AND DEADLATCH FROM BOTH 

SIDES OF THE DOOR.

 REMOVE THE 

INTER-CONNECT CAM, AND INSTALL

THE OPTIONAL DOUBLE 

INTER-CONNECT CAM.

4.200

1.125

ONE WALL ONLY

2.310

1.212

1.160

3.306

5.025

.500

ONE WALL ONLY

FOR 

ELECTRIFIED OPTION

1.125

THRU ONE

WALL ONLY

2.520

.196

ONE WALL ONLY

4x,  .177

.968

.928

.928

.968

BACKSET

FOR INSWING DOORS USE SMALL FORMAT LEVERS (4600)

AND REFER TO 4600 INSTRUCTION WITH 2190

6.885

1.010

R.156

4x

6.375

1.594

CL OF 

CYLINDER

OUTSWING LOCK STILE PREPARATION ONLY

4.200

.938

.968

1.250 

BOTH WALLS

FOR CYLINDER

.875

ONE  WALL ONLY

2.238

.177

.196

ONE WALL ONLY

4x,  .177

.196

ONE WALL ONLY

1.212

1.160

3.390

2.520

.968

.938

BACKSET

5.375

4.645

1.447

.080

2 PLS

C'SNK FOR #10 

FLAT HD SCREW

.218

.572

ALUMINUM FRAME

CL OF

CYLINDER

DEADLATCH

IN DOOR CL

2101 STRIKE PLATE

SHOWN

CL OF

STRIKE PLATE

(2 15/32")

FOR RADIUS FACEPLATE 

WITH WEATHERSEAL ONLY !

- WITH A SMALL FLAT HEAD 

  SCREWDRIVER, PRY OFF 

  BEVEL TABS AS SHOWN.

 

LHR BEVEL

RHR BEVEL

FLAT or RADIUS

 

 

- YOU WILL ALSO HAVE TO RE-ORIENT

  THE INTER-CONNECT CAM:

a)

 LOOSEN THE #6-32 FLAT HEAD SCREW 

    AT THE BOTTOM OF THE LOCK.

b)

 ROTATE THE INTER-CONNECT CAM 

    TO  THE SAME DIRECTION AS THE

    LATCH BOLT BEVEL.

    RETIGHTEN THE #6-32 FLAT HEAD 

    SCREW TO COMPLETE THE 

    OPERATION.

#6 x1/2"

BOLT SCREW

LATCH 

BOLT

1-1/2" BACKSET

SHOWN

3a

TO CHANGE THE HANDING

ON LATCH BOLT:

- DEPRESS THE LATCHBOLT UNTIL BOLT SCREW CAN BE

  SEEN THROUGH CASE HOLE. (1-1/2" BACKSET ONLY). 

- REMOVE BOLT SCREW AND ORIENT LATCH BOLT TO

  THE OPPOSITE HAND.

- DEPRESS THE LATCH BOLT UNTIL THE COUNTERSINK

  HOLE ON THE LATCH BOLT CAN BE SEEN THROUGH THE

  CASE HOLE AS SHOWN IN 

FIG.1.

- REINSERT BOLT SCREW  AND TIGHTEN TO 22 - 27 IN-LB.

#1-64 x 1/4"

FLAT HEAD SCREW

INTER-

CONNECT CAM

BACK VIEW

BEVELED

SIDE SHOULD

FACE THE SAME

DIRECTION AS THE

INTER-CONNECT

CAM

LATCH

BOLT

 

 

 

 

#6-32

FLAT HD

SCREW

a

b

1-1/8 BACKSET

6.375

1.340

2x

#10-32

ONE WALL ONLY

BACK OF LOCK STILE

DOUBLE INTER-

CONNECT CAM

(P/N 27-0268)

3b

1-1/2 BACKSET

FIG.1

STRIKE PREPARATION

BEVEL TABS ADJUSTMENT

- ROTATE BEVEL TABS TO DESIRED HANDING.

  USING THE BEVEL ADJUSTMENT ALLOWS THE FLAT. 

  FACEPLATE TO WORK IN BEVEL STILES

( INTERIOR TRIM )

( EXTERIOR TRIM )

- APPLY STICK ON TEMPLATE OVER CYLINDER BACKSET CENTER LINE.

  

NOTE: EACH TEMPLATE IS LABELED FOR OUTSIDE OR INSIDE TRIM.

- CENTER PUNCH ALL HOLES.

- DRILL HOLES AT CENTER PUNCH LOCATIONS. REMOVE TEMPLATE.

- INSTALL 2190 PER INSTALLATION INSTRUCTIONS.

1

3

2

TOOLS NEEDED:

- 5/64 ALLEN WRENCH

- 3/32 ALLEN WRENCH

- 1/8   ALLEN WRENCH

- #9     DRILL BIT (.196 Ø)

- #16   DRILL BIT (.177 Ø)

- 7/8    DRILL BIT (.875 Ø)

- 1-1/8 DRILL BIT (1.125 Ø )

INSTALLATION OF STRIKE

- INSERT MOUNTING BACK PLATE BEHIND JAMB AND FASTEN WITH 

  #10 FLAT HEAD SCREWS.

- INSERT TRIM BOX WITH 2101 STRIKE PLATE AND FASTEN WITH

  #10 FLAT HEAD SCREWS TO BACK PLATE AS SHOWN.

3a

TO BLOCK HOLDBACK FEATURE:

- INSTALL #1-64 x 1/4" FLAT HEAD 

  SCREW INTO CASE AS SHOWN 

  BEFORE INSTALLING IN DOOR.

Page     of

1

3

INSTALLATION INSTRUCTIONS

Rev.

Appvd: BC

Date:

ECN: 11883

Date: 02/09/12

D

2190 INSTALLATION INSTRUCTIONS    

W/ HEAVY DUTY ENTRANCE LEVER SET

80-0180-410

Adams Rite Manufacturing Co.

260 Santa Fe Street,

Pomona, CA 91767

Phone:  909-632-2300

Fax:  909-632-2369

www.adamsrite.com

02/03/2012

Reviews: