ZyXEL Communications IES-1248-51 User Manual Download

Page: 373 / 385

IES-1248-51 User’s Guide

373

P P E N D I X

IES-1248-51 Specifications

This chapter provides the specifications for the IES-1248-51.

Physical Specifications

The IES-1248-51 is 19 inch (482.6mm) rack-mountable.

Telco-50 Connectors

The IES-1248-51 has 4 Telco-50 connectors. Connect the two

USER

Telco-50 connectors to

the subscribers and two

Telco-50 connectors to the PSTN switch.

Dimensions

1.5U 439.8 mm (W) x 251 mm (D) x 66 mm (H)

Weight

7.2 kg

Wire Gauge Specifications

The following table shows the specifications for wire gauge.

AWG (American Wire Gauge)

is a measurement system for wire that specifies its thickness.

As the thickness of the wire increases, the AWG number decreases.

Power Input

-36 ~ -72 VDC, 2.5 A maximum.

Power Consumption

90 W maximum

Table 96

Wire Gauge Specifications

WIRE TYPE

REQUIRED AWG NO. (DIAMETER)

Ground Wire

18 or larger

Telephone Wire

26 or larger

IES-1248-51 Power Wire

16 to 18

Summary of Contents for IES-1248-51


































































































































































































































































































































































































Search results

Summary of Contents for IES-1248-51

Reviews:

Related manuals for IES-1248-51

Brands by name

Popular brands

ZyXEL Communications IES-1248-51, User Manual

Search results

Summary of Contents for IES-1248-51

Reviews:

Related manuals for IES-1248-51

Brands by name

Popular brands