ZWICK TRI-CHECK Series Operation Instructions Manual Download Page 13

Operation instructions Butterfly Check Valve Series TRI-CHECK, with 

counter weight and optional hydraulic damper 

ZWICK Armaturen GmbH  D-58256 Ennepetal

 

Instructions No.

 

Zw-Tri-Check-2016 / Rev.11 

12

 

10  EU directives 

 

Declaration of conformity acc. to: till 2016/07/18 Directive 97/23 EC (Article 13, Directive 2014/68/EU) 
Declaration of conformity acc. to: from 2016/07/19 Directive 2014/68/EU 
Manufacturer's declaration acc. to: Directive 06/42 EC 
Manufacturer's declaration acc. to: till 2016/04/19 Directive 94/9 EC 
Manufacturer's declaration acc. to: from 2016/04/20 Directive 2014/34/EU

 

 

The Manufacturer 

ZWICK GmbH, D-58256 Ennepetal 

explains that the valve  

Butterfly valve Series TRI-CHECK  

 with counter weight 

 with optional hydraulic damper 

 

EC Directives 

Directive 97/23 EC 

or Directive 2014/68/EU

 

Directive 06/42 EC

 

Directive 94/9 EC 

or Directive 2014/34/EU

 

1.  is  a  pressurized  equipment within 

the meaning of the EC pressure 
equipment directive 97/23 EC or 
directive 2014/68/EU and complies 
with the requirements of this 
directive   

2.  may be only operated under 

consideration of the supplied 
operating instruction no. Zw-
TriBlock-2016. 

3.  is in conformance with article 13 of 

the EU directive 2014/68/EU and 
that this article has been 
considered 

4.  is a partly completed machinery (applies 

only to model that has an actuator) within 
the meaning of art. 2 g of the directive 
06/42 EC (machine directive) and is only 
intended to be installed in a completed 
machinery 

5.  must not be put into service unless it is 

incorporated in a completed machinery 
which has been declared in conformity with 
this directive 

6.  fulfills the declared requirements of this 

directive 

7.  may be only operated under consideration 

of the supplied operating instruction no. 
Zw-Tri-Check-2016. 

 

(without actuator/accessories) 

8.  has been submitted to a hazard 

analysis according to directive 94/9 
EC 

9.  has no own source of ignition and 

can  therefore be used in an 
explosive atmosphere 

10.  cannot comply with the directive 

94/9/EC or directive 2014/34/EU 

11.  may be only operated under 

consideration of the supplied 
operating instruction no. Zw-Tri-
Check-2016, especially chap. 8 

Note: 

Electrical/pneumatic/hydraulic 
actuators and accessories have to 
be submitted to a separate 
assessment of conformity according 
to directive 94/9 EC. 

The activation of this valve is only allowed if the valve is attached on both sides to the pipe, which excludes danger of injury.    

Applied EU directives and standards:  

97/23 EC 

2014/68/EU 

EN 593 

EN 12516  

94/9 EC 

2014/34/EU 

EN 1127-1 

EN 13463-1 

06/42 EC 

EC Pressure Equipment Directive 

EU Pressure Equipment Directive 2014 

Industrial valves – Metallic butterfly valves 

Industrial valves – Shell design strength 

European explosion-protection directive 

European explosion-protection directive 2014 

Explosive Atmospheres – Explosion prevention and protection 

Non-electrical equipment for potentially explosive atmospheres  

EC Machine Directive 

Type description and technical characteristics:  
ZWICK Catalogue <Butterfly valves Series TRI-CHECK> 

 

Authorized person to compile technical documentation:  
Daniel Zwick, D-58256 Ennepetal 

 

Applied conformity assessment procedure: 

for Directive 97/23 EC on pressure equipment or from 2016/07/19 Directive 2014/68/EU, category: acc. table 1, module H 

Name of the notified body:  

Identification no. of the notified body:  

LRQA GmbH Hamburg 

0525 

 

 

 

Summary of Contents for TRI-CHECK Series















Reviews: