background image

8

     (c) 2012 Z-Wave Europe GmbH, Goldbachstr. 13, 09337 Hohenstein-Ernstthal, Germany, www.zwaveeurope.com

pressed, sensor triggers, ...). In case the event happens all devices stored in the respective association group will receive a
common wireless command.

Association Groups:

1

Battery Status and Sensor Report (max. nodes in group: 1)

2

Sensor Triggered (max. nodes in group: 3)

Configuration Parameters

Z-Wave products are supposed to work out of the box after inclusion, however certain configuration can adapt the function better
to user needs or unlock further enhanced features.

IMPORTANT: Controllers may only allow configuring signed values. In order to set values in the range 128 … 255 the value sent in
the application shall be the desired value minus 256. For example: to set a parameter to 200  it may be needed to set a value of
200 minus 256 = minus 56. In case of a two byte value the same logic applies: Values greater than 32768 may needed to be given
as negative values too.

Basic Level Set (Parameter Number 1, Parameter Size 1) 

Set basic set value to be on or off

Value

Description

0

Disable

1 — 99

Use value (Default 99)

Temperature Trigger ON value (Parameter Number 2, Parameter Size 1) 

Temperature level when a ON

command is sent out

Value

Description

236 — 255

Trigger On on

0 — 50

Trigger On on

99

Disable (Default)

Temperature Trigger OFF value (Parameter Number 3, Parameter Size 1) 

Trigger Temperature level when a

OFF command is sent out

Value

Description

236 — 255

Trigger Off on

0 — 50

Trigger Off on

99

Disable (Default)

Humidity Trigger ON value (Parameter Number 4, Parameter Size 1) 

Humidity level when a ON command is

sent out

Value

Description

20 — 90

Trigger On on

Summary of Contents for Everspring EVR_ST814











Reviews: