Zwave Everspring EVR_ST814 Manual Download Page 9

Page: 9 / 10

Disable (Default)

Humidity Trigger OFF value (Parameter Number 5, Parameter Size 1)

Humidity level when a OFF command is

sent out

Value

Description

20 — 90

Tigger Off on

Disable (Default)

Auto Report Time (Parameter Number 6, Parameter Size 2)

Sets the time interval when a sensor report is sent

Value

Description

Disable (Default)

1 — 1439

Auto report periodically

Auto Report Temperature (Parameter Number 7, Parameter Size 1)

Sets the temperature change causing a

sensor report

Value

Description

Disabled (Default)

1 — 70

Auto report on temp. change

Auto Report Humidity (Parameter Number 8, Parameter Size 1)

Sets the humidity change causing a sensor

report

Value

Description

Disable (Default)

5 — 70

Auto report on humidity change

Command Classes

Supported Command Classes

Basic (version 1)

●

Multi Channel (version 2)

●

Wake Up (version 2)

●

Association (version 2)

●

Version (version 1)

●

Battery (version 1)

●

Configuration (version 1)

●

Multilevel Sensor (version 2)

●

Manufacturer Specific (version 1)

●

Technical Data

Summary of Contents for Everspring EVR_ST814











Search results

Summary of Contents for Everspring EVR_ST814

Reviews:

Brands by name

Popular brands

Zwave Everspring EVR_ST814, Manual

Search results

Summary of Contents for Everspring EVR_ST814

Reviews:

Brands by name

Popular brands