ZSK Automatic Bobbin Winder Operating Manual Download Page 17 | Manualshive

Page: 17 / 26

background image

02418V10 • 11.08.2016/DC •

1-17

Adjustments

1.10 Adjustments

1.10.1 Adjust thread tension

The thread tension will be adjusted with the knurled ring of the rear and front

tension regulator

Clockwise rotation



Thread tension is increased

Counter clockwise rotation



Thread tension is decreased

The thread tension has to adjusted with both knurled rings, so

that the bobbins will be ﬁ lled not to tight and that after thread

cutting the thread breakage sensor not interrupted the winding

process.

The correct thread tension at the bobbin case is shown in the ﬁ gures below:

Rear tension regulator

Thread brackage sensor

Front tension regulator

Retracting bow

«
...
15
16
17
18
19
...
»

Summary of Contents for Automatic Bobbin Winder



























Reviews:

No comments

Related manuals for Automatic Bobbin Winder

Brand: Olivetti Pages: 39

Brand: PACIFIC CYCLE Pages: 112

Brand: E+E Elektronik Pages: 14

Brand: E+E Elektronik Pages: 26

Brand: E+E Elektronik Pages: 28

Brand: E+E Elektronik Pages: 2

Brand: BW Pages: 8

Brand: Napoleon Pages: 4

Brand: Napoleon Pages: 4

Brand: Napoleon Pages: 2

Brand: Sanitas Pages: 52

Brand: Tait Pages: 46

Brand: Tait Pages: 9

Brand: Tait Pages: 89

Brand: Tait Pages: 20

Brand: Xsens Pages: 53

Brand: Smartech Pages: 8

LCD Touch BacPac

Brand: GoPro Pages: 25

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands