Zoom 5363 User Manual Download

Page: 121 / 142

Table 33. L2TP/PPTP Menu Option

Option

Description

PPP Address Range
(Start/End)

Configure the dedicated IP address pool for L2TP/PPTP. The
LAN IP subnet at one end of the VPN tunnel must be different
from the LAN

IP subnet at the other end of the VPN tunnel. For example, if
one side’s LAN subnet is 192.168.

.x, then the other side

should be 192.168.

.x (where the subnet mask in this

example is 255.255.255.0).

Select Enable to enable MPPE (Microsoft Point-to-Point
Encryption). MPPE is used to enhance the confidentiality of
PPP-encapsulated packets. It uses the RSA RC4 encryption
algorithm.

PPP Security (MPPE
Encryption)

Enter the user name for the L2TP or PPTP tunneling.

Username

Enter the password for the L2TP or PPTP tunneling.

Password

Re-enter to confirm the password.

Confirm Password

Show the existing user list.

User List

L2TP Server
(Preshared Phrase)

Enter a key (Pre-Shared key) for authentication. This key is
used by IPSec to validate the computer as a trusted machine.

121

Summary of Contents for 5363















































































































































Search results

Summary of Contents for 5363

Reviews:

Related manuals for 5363

Brands by name

Popular brands

Zoom 5363, User Manual

Search results

Summary of Contents for 5363

Reviews:

Related manuals for 5363

Brands by name

Popular brands