Zontes ZT350-V1 Service Manual Download Page 80

Page: 80 / 120

、

FRONT FORK COMPONENT

CHK

ADJ

NO.

PART NO.

PART NAME

QTY

CAUTION

1244200-074000 ZT310-T windshield motor sheath

1244200-075000 ZT310-T windshield front rocker buffer rubber

1184200-074000 ZT310-T windshield motor

Fig.19FRONT FORK
COMPONENT

Windshield motor sub-assembly

PROCEDURE:

●

Windshield motor parts

Remove the motor sheath

⑴

and 4 pieces of cushion rubber

⑷

Grab the lower left rocker arm

⑹

. Remove the 2 screws

⑶

with a Phillips screwdriver and remove. Remove

the rocker arm clamp

⑵

Grab the lower right rocker arm

⑺

. Remove the 2 screws

⑶

with a Phillips screwdriver and remove. Remove

the rocker arm clamp

⑵

CAUTION:

●

Do not pull the cable directly when pulling the plug.

●

Pay attention to the limit plane and limit groove of the motor and rocker clamp when reassembling.

4024200-081051

ZT310-T mounting plate of head cover ( lower rocker
(dark gray matte)

1250201-046000

GB818 cross recessed pan head screw M4×16
(environmental color)

4024200-079051

ZT310-T lower left rocker of head cover (dark gray
matte)

4024200-080051

ZT310-T lower right rocker of head cover (dark gray
matte)

Summary of Contents for ZT350-V1

























































































































Search results

Summary of Contents for ZT350-V1

Reviews:

Related manuals for ZT350-V1

Brands by name

Popular brands

Zontes ZT350-V1, Service Manual

Search results

Summary of Contents for ZT350-V1

Reviews:

Related manuals for ZT350-V1

Brands by name

Popular brands